RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: blueagle
Showing results 1 to 12 of 12
Search took 0.29 seconds.
Forum: Speed - RC Gas Boats
12-17-2009, 05:06 AM
Replies: 13
Views: 1,170
Posted By blueagle

RE: HELP!!! with twin tunning setup

You have got your needle settings the wrong way round,( 2 on the low and 1 on the high)
Forum: Speed - RC Gas Boats
08-07-2009, 03:36 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

Hi Mike, I set mine up with about 20* each side to start with, and found that to be a bit much and my servos to be a bit fast so I have come back to some where between
10* and 15* and slowed the...
Forum: Speed - RC Gas Boats
08-03-2009, 03:39 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

Thanks Chris, 2 more pics, I'v got a 1lt gas tank in cockpit area with 200ml cable oil supply on top of that and a 1lt bag in the nose with 450ml of water in it, that puts the CG at36%
Hooters,...
Forum: Speed - RC Gas Boats
08-03-2009, 03:25 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

I can only send 2 at a time, they must be a bit big.
Forum: Speed - RC Gas Boats
08-03-2009, 03:20 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

Hi Guys, here's some more pic's as promised.
Forum: Speed - RC Gas Boats
08-02-2009, 07:06 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

HI Hooters, Yeah that right 90# manifold, George at Hobby Depot can get them, give him a call.
BLUE.
Forum: Speed - RC Gas Boats
08-02-2009, 06:58 AM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

Hi YPC I was one step infront of you with the EX bracket, I have removed the original and replaced it with a welded on bracket from under the stinger down to the cav' plate.
For the carby I have...
Forum: Speed - RC Gas Boats
08-01-2009, 11:42 PM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

Steering servos are twin Hitec HS 5745 MG's they seem to have plenty of grunt, I've had to slow them down a lot.
BLUE.
Forum: Speed - RC Gas Boats
08-01-2009, 05:10 PM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

The pics I sent didn't seem to work, Ill try again.
BLUE
Forum: Speed - RC Gas Boats
08-01-2009, 04:59 PM
Replies: 2,360
Views: 510,570
Posted By blueagle

RE: GAS OUTBOARD guys this is our new home

HI Ian, Good to have all this stuff in one place (well done) I have one of Jordo's hulls with a lawless leg on it and have given it one run, had a few carby problems to sort
but got it close, I...
Forum: Speed - RC Gas Boats
12-22-2008, 04:16 PM
Replies: 20
Views: 3,658
Posted By blueagle

RE: Slam 260

Mate,,, It's a Zenoah based engine, 34mm bore/28mm stroke/ 50mm rod length, what ever you can do to a Zenoah you can do to a slam!! and because of the smaller cases you can sit it lower in the boat...
Forum: Speed - RC Gas Boats
12-22-2008, 07:41 AM
Replies: 20
Views: 3,658
Posted By blueagle

RE: Slam 260

Hi Guys, it's good to see you talking about the SLAM 260.

The motor was built to be a user friendly off the shelf affordable product. The modifications reflect this which does not make it a...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.