RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: Krysta
Showing results 1 to 25 of 500
Search took 1.05 seconds.
Forum: O.S. Engines Support
11-25-2014, 09:50 AM
Replies: 0
Views: 770
Posted By Krysta

OS 105HZ-R Engine

From BAX at OS/Hobby Services:

To our Fellow modelers:



The OS 105HZ-R was designedfor maximum performance but with many of the lower nitro fuels that areavailable now we have found that...
Forum: Futaba Radios Direct support forum
10-31-2013, 05:34 AM
Replies: 1
Views: 738
Posted By Krysta

The 14MZ with the TM14 module is not capable of...

The 14MZ with the TM14 module is not capable of Telemetry. These will not link.

For information on which transmitters and receivers are compatible with each other, please see our website;
...
Forum: Futaba Radios Direct support forum
10-30-2013, 11:28 AM
Replies: 1
Views: 1,258
Posted By Krysta

There's not much difference if you have already...

There's not much difference if you have already done this on other Futaba radios. It's basically the same although easier than some of the non-computerized ones in having a Function menu which allows...
Forum: Futaba Radios Direct support forum
10-30-2013, 11:16 AM
Replies: 3
Views: 641
Posted By Krysta

You will find the the PDF version of what is in...

You will find the the PDF version of what is in every update we have had by checking this link at the very bottom of the Update page;

http://downloads.hobbico.com/software/fut/


This will have...
Forum: Futaba Radios Direct support forum
10-30-2013, 11:00 AM
Replies: 2
Views: 473
Posted By Krysta

Yes, on some of the transmitters it is coded into...

Yes, on some of the transmitters it is coded into the serial number, although there are a few lower channel transmitters where this is not the case.

Please let us know what transmitter you have. ...
Forum: Futaba Radios Direct support forum
10-30-2013, 10:57 AM
Replies: 2
Views: 424
Posted By Krysta

Hi Darren, Make sure your Airbrake is set...

Hi Darren,

Make sure your Airbrake is set to a 3 position switch and is active. Then on the switch selection screen, set the On/Off position to the middle. If you set your rates here at 50% you...
Forum: Futaba Radios Direct support forum
10-30-2013, 08:30 AM
Replies: 3
Views: 1,068
Posted By Krysta

Sledge, this would on the bottom of the...

Sledge, this would on the bottom of the transmitter next to the Serial number.

But either way, if there is one on not, it still sounds like it needs to come into the service center to be checked....
Forum: Futaba Radios Direct support forum
10-28-2013, 05:54 AM
Replies: 3
Views: 1,068
Posted By Krysta

You may want to check the serial number of your...

You may want to check the serial number of your transmitter to make sure it does not fall in the 07 or A7 range per the Advisory that occured quite a few years ago:

Futaba 6EX, 7C and TM-7 Service...
Forum: Futaba Radios Direct support forum
10-21-2013, 08:32 AM
Replies: 4
Views: 453
Posted By Krysta

Are you going into PMIX2 to do your second mix? ...

Are you going into PMIX2 to do your second mix?

Make sure in PMix 1 where you are negating channel 6 in the radio that you do not set this to ANY switch, just leave the switch to ON.

Then go...
Forum: Futaba Radios Direct support forum
10-21-2013, 08:20 AM
Replies: 5
Views: 1,768
Posted By Krysta

The neutral dead band of a servo also depends on...

The neutral dead band of a servo also depends on what transmitter and receiver you are using.

This is not something we can easily answer.

Sincerely,Krysta
Product Development & Support...
Forum: Futaba Radios Direct support forum
10-21-2013, 08:17 AM
Replies: 1
Views: 354
Posted By Krysta

The BLS251 is a Super Narrow Pulse servo used...

The BLS251 is a Super Narrow Pulse servo used only with a compatible Futaba Gyro.

It will not work as a normal servo in your receiver.


Sincerely,Krysta
Product Development & Support...
Forum: Futaba Radios Direct support forum
10-17-2013, 06:06 AM
Replies: 4
Views: 453
Posted By Krysta

Before you do your mix from rudder to nose wheel,...

Before you do your mix from rudder to nose wheel, you would need to negate the flap switch from affecting any programming.

So you will need to do one Pmix with Channel 6 as Master and then also...
Forum: Futaba Radios Direct support forum
10-17-2013, 05:45 AM
Replies: 2
Views: 2,096
Posted By Krysta

Hi Daniel, Per your email to us at Futaba...

Hi Daniel,

Per your email to us at Futaba Support also, I will just restate that it sounds as though something on the main board in the dial sensor is bad.

You would need to return this to...
Forum: Futaba Radios Direct support forum
10-07-2013, 11:09 AM
Replies: 2
Views: 6,726
Posted By Krysta

What wing type did you choose in your 14SG? ...

What wing type did you choose in your 14SG?

If you chose, Normal, 2-ail and Normal tail. Then I would just go into Camber mix in the Model menu, activate Camber mix, set this on a slider, then...
Forum: Futaba Radios Direct support forum
10-07-2013, 10:59 AM
Replies: 1
Views: 503
Posted By Krysta

Per the instructions for the AnyLink, yes, you...

Per the instructions for the AnyLink, yes, you need to remove the module.

http://manuals.hobbico.com/tac/tacj2000-manual-v2.pdf

When removing the module, be carefull to pull it straight out...
Forum: Futaba Radios Direct support forum
10-02-2013, 06:38 AM
Replies: 4
Views: 397
Posted By Krysta

Sorry to hear that its still not working. ...

Sorry to hear that its still not working.

The closest Distributor to you would be;

AUSTRALIA
RC Wholesale Australia Pty. Ltd. (http://www.rcwholesale.com.au/)
Unit 15 / 49 Great Eastern...
Forum: Futaba Radios Direct support forum
09-25-2013, 06:20 AM
Replies: 2
Views: 591
Posted By Krysta

We are not sure why they have given you...

We are not sure why they have given you information like this.

The SR10 works fine for both Analog and Digital servos, with no lack of response or problems with speed.

FEATURES: Perfect for...
Forum: Futaba Radios Direct support forum
09-25-2013, 06:15 AM
Replies: 3
Views: 515
Posted By Krysta

The ABS will not work the same on electric as it...

The ABS will not work the same on electric as it will on Nitro vehicles. For one you are asking it to override the settings in your ESC, but basically Nitro and Electric do not "brake" the same.
...
Forum: Futaba Radios Direct support forum
09-24-2013, 11:36 AM
Replies: 3
Views: 750
Posted By Krysta

If you check in your Function screen, you will...

If you check in your Function screen, you will see Elevator listed as (depending on your wing type) Aux 7.

So you would go into the ARF screen and set Expo in Aux 7.

Sincerely,Krysta
Product...
Forum: Futaba Radios Direct support forum
09-24-2013, 09:28 AM
Replies: 1
Views: 419
Posted By Krysta

We have not heard of this problem here in the...

We have not heard of this problem here in the Service Center.

I would recommend you send this in so that we can check this out for you.

Sincerely,Krysta
Product Development & Support...
Forum: Futaba Radios Direct support forum
09-24-2013, 09:26 AM
Replies: 4
Views: 397
Posted By Krysta

Try going into a completely blank model and see...

Try going into a completely blank model and see if these EPA adjustments change your subtrim. Normally you should set the End Points first before setting any Subtrim. And subtrim is only meant to be...
Forum: Futaba Radios Direct support forum
09-20-2013, 10:35 AM
Replies: 5
Views: 1,302
Posted By Krysta

The setup would be the same for the 14SG also. ...

The setup would be the same for the 14SG also.

Sincerely,Krysta
Product Development & Support Specialist
Futaba Service Center USA
[email protected]
Forum: Futaba Radios Direct support forum
09-20-2013, 06:42 AM
Replies: 5
Views: 1,302
Posted By Krysta

First make sure you get the WTR bound to the...

First make sure you get the WTR bound to the 14MZ. Remove the WTR from the 14MZ, plug it into the 18MZ.

Go back the 14MZ, turn the Trainer back to INH.

On the 18MZ the switch should be on or...
Forum: Futaba Radios Direct support forum
09-20-2013, 05:53 AM
Replies: 3
Views: 750
Posted By Krysta

Not sure if this is what you are looking for or...

Not sure if this is what you are looking for or not, but you could do a mix of Rudder2 as master, with Rudder2 again as slave, set the rates to -100% both ways and put this on a switch. When you...
Forum: Futaba Radios Direct support forum
09-06-2013, 08:40 AM
Replies: 4
Views: 659
Posted By Krysta

I am not 100% sure if this is what you are trying...

I am not 100% sure if this is what you are trying to acheive, but I have found that the easiest way to do this is with just one Pmix, which you already have; Throttle as Master and channel 7 as...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.