RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: farooq
Showing results 1 to 15 of 15
Search took 0.25 seconds.
Forum: Gas Engines
01-20-2010, 02:16 AM
Replies: 4
Views: 870
Posted By farooq

RE: what motor del30 or Evolution Engines 26GX

A 50CC gasser weighs about 17.5 pounds and only gives enough power for hovering. for a 13pounds plane you need to deploy a bigger engine to get good hover. May be you should look an MT35 or ZDZ 40...
Forum: Gas Engines
01-03-2010, 11:58 AM
Replies: 8
Views: 1,822
Posted By farooq

DL50 to DLE55 Conversion

Can i convert DL50 to DLE55
Forum: Gas Engines
01-03-2010, 11:53 AM
Replies: 6
Views: 1,000
Posted By farooq

RE: DL50 Problem

Thanks for the tips. Today I again checked the engine played with the needles once again but unable to get the power and top-end 500 rpms back. Furthermore the engine was giving weired sound too.
...
Forum: Gas Engines
01-01-2010, 08:56 AM
Replies: 6
Views: 1,000
Posted By farooq

DL50 Problem

I am using DL-50 on 50CC Edge 540. Configuration:
23X8 Xoar Prop
50:1 Mobil Racing 2T
The engine has about 80 flights.

4 months back when temp was around 36C@1800Feet it was revolving at...
Forum: Gas Engines
08-27-2009, 06:53 AM
Replies: 59
Views: 12,301
Posted By farooq

RE: DLE 55 or MT 57

Super08

What about the vibration and engine transition.
Forum: Gas Engines
08-26-2009, 11:36 AM
Replies: 59
Views: 12,301
Posted By farooq

RE: DLE 55 or MT 57

Did you guys try with the timing adjustment with MT-57
Forum: Giant Scale Aircraft - 3D & Aerobatic
08-18-2009, 12:35 PM
Replies: 67
Views: 13,160
Posted By farooq

RE: RC Pilot 50cc Build

On one of the planes "50CC Edge 540 - II from PAU" I had to bring motor incidence to 1.75 Degrees to rectify the situation.
Forum: Giant Scale Aircraft - 3D & Aerobatic
08-13-2009, 10:45 AM
Replies: 67
Views: 13,160
Posted By farooq

RE: RC Pilot 50cc Build

Hi AirTech

I was just going through the thread and was having question about the incidence angle of the engine. When we have aroung 1.5 degrees of down thrust how can we main the incidence...
Forum: Giant Scale Aircraft - General
07-06-2009, 07:25 AM
Replies: 0
Views: 434
Posted By farooq

Pilot-rc 50CC YAK Setting

I am looking for correct setting for the pilot rc 50CC YAK. I am using DL-55 with stock mufflers and standoffs. Rx battery is A123 racing 2300mAH with out regulator on AR7100. Ignition battery is...
Forum: Gas Engines
06-21-2009, 09:59 AM
Replies: 29
Views: 10,943
Posted By farooq

RE: DL50 Ignition timing setting guide.

Thanks everyone. <div>
</div><div>I have finally checked the timing and figured out that its 32 degrees. I changed the timing to 28 degrees but as demonstrated in the vide link given...
Forum: Gas Engines
06-15-2009, 07:15 AM
Replies: 29
Views: 10,943
Posted By farooq

DL50 Ignition timing setting guide.

Hi

Ineed to set the ignition timing setting on my DL50. Can anyone guide me the simplest and accurate method. I have no previous knowledge or special tool for it.
Forum: Gas Engines
06-14-2009, 10:46 PM
Replies: 15
Views: 1,979
Posted By farooq

RE: DL55 rpm transitioning problem

OK guys. I tried the new setting with leaner low end setting. Without cowl I was getting 6600 rpm peak, good transitioning. But when i lowered the throttle sometimes engine comes back at 1500 rpm and...
Forum: Gas Engines
06-12-2009, 06:53 AM
Replies: 15
Views: 1,979
Posted By farooq

RE: DL55 rpm transitioning problem

Thanks for the guidance. I shall try to lean the low needle and fly this week end and inform about the results
Forum: Gas Engines
06-10-2009, 10:13 AM
Replies: 15
Views: 1,979
Posted By farooq

DL55 rpm transitioning problem

I am using DL55 on yak 54. I am using 35:1 organic lubricant. Temp here is 37 degree Celcius. Height is 1800 Feets. Iam getting maximum rpm of 6450 to 6600 using 23X8 Xoar prop. I have done break in...
Forum: Questions and Answers
05-27-2009, 12:45 AM
Replies: 4
Views: 1,831
Posted By farooq

RE: Pilot RC 30% Yak 54

how did you tighten the two lower screws of the cowl
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.