RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: hyltaiwan
Showing results 1 to 25 of 30
Search took 0.26 seconds.
Forum: Gas Engines
06-08-2022, 06:05 PM
Replies: 2
Views: 691
Posted By hyltaiwan

It is M15 x 1 thread.

It is M15 x 1 thread.
Forum: Gas Engines
01-03-2022, 07:39 PM
Replies: 9
Views: 1,435
Posted By hyltaiwan

Ha Ha, someone is helping him by controlling the...

Ha Ha, someone is helping him by controlling the throttle stick on the Tx.
Forum: Gas Engines
10-03-2021, 06:51 PM
Replies: 2
Views: 1,857
Posted By hyltaiwan

Check your drive flange, I guess the screw pin of...

Check your drive flange, I guess the screw pin of the drive flange was broken and the ignition timing now is not at the correct position {orientation).
Forum: Gas Engines
02-10-2021, 01:22 AM
Replies: 300
Views: 81,086
Posted By hyltaiwan

Check that 4 pcs of cylinder screw, if they are...

Check that 4 pcs of cylinder screw, if they are loosen your valve clearance will be enlarged quite a litlle.
Forum: Gas Engines
07-31-2017, 06:47 PM
Replies: 2,806
Views: 706,730
Posted By hyltaiwan

You have to turn two complete revolutions to feel...

You have to turn two complete revolutions to feel three compression TDC.
Forum: Gas Engines
02-02-2017, 07:30 PM
Replies: 640
Views: 252,051
Posted By hyltaiwan

FG90R3 seems run much better than FG84R3. But I...

FG90R3 seems run much better than FG84R3. But I didn't make a record on temperature.
I started the break in Nov. last year and I had some other project on hand so I didn't complete it yet.:p
Forum: Gas Engines
01-29-2017, 10:46 PM
Replies: 640
Views: 252,051
Posted By hyltaiwan

https://youtu.be/-RTwzPTGRRE Try it this...

https://youtu.be/-RTwzPTGRRE

Try it this way, it will help your entire break in procedure
more evenly for every cylinder.
Forum: Gas Engines
09-29-2016, 11:57 PM
Replies: 640
Views: 252,051
Posted By hyltaiwan

12mm for the shaft without thread

12mm for the shaft without thread
Forum: Gas Engines
09-27-2016, 09:47 PM
Replies: 3
Views: 2,217
Posted By hyltaiwan

You should always use the steel washer which came...

You should always use the steel washer which came with engine.
No matter you use the prop nut or anti loosening nut.
Forum: Gas Engines
08-02-2015, 05:19 PM
Replies: 2,806
Views: 706,730
Posted By hyltaiwan

The material of cylinder gasket and camgear cover...

The material of cylinder gasket and camgear cover gasket will deform under heat, that is why you should check every cylinder screws
and camgear cover screws during initial stage of break-in as...
Forum: Gas Engines
01-28-2015, 01:58 AM
Replies: 18
Views: 5,394
Posted By hyltaiwan

That is a M3.5 0.5pitch thread, you can buy the...

That is a M3.5 0.5pitch thread, you can buy the cylinder screw set for SAITO 91S.
Solder it with a rod, and you got what you want.
Cut it to leave only 5mm long or you might touch the low needle...
Forum: Gas Engines
08-12-2014, 01:21 AM
Replies: 300
Views: 81,086
Posted By hyltaiwan

This part No. had been announced Jan 2014. We...

This part No. had been announced Jan 2014. We have it here in Taiwan
.http://www.rcuniverse.com/forum/attachment.php?attachmentid=2021775
Forum: Gas Engines
08-11-2014, 10:04 PM
Replies: 300
Views: 81,086
Posted By hyltaiwan

What you need is G14122.(SAIG14122)

What you need is G14122.(SAIG14122)
Forum: Gas Engines
12-09-2013, 07:52 PM
Replies: 1,824
Views: 342,155
Posted By hyltaiwan

OK, let's try again. 1. Make sure you have...

OK, let's try again.
1. Make sure you have never take out the cam gear housing.(you have correct cam gear timing,or the following steps will be useless)
2.Take both rocker arm cover off, take...
Forum: Gas Engines
12-09-2013, 01:00 AM
Replies: 1,824
Views: 342,155
Posted By hyltaiwan

Since you said you have badly carbon built up on...

Since you said you have badly carbon built up on both piston and top of cylinder, I guess you have small piece carbon or dirt seated on the valve seat.
If you have not yet have your engine...
Forum: Gas Engines
10-09-2013, 07:23 PM
Replies: 2
Views: 405
Posted By hyltaiwan

M4 x 0.7

M4 x 0.7
Forum: Gas Engines
02-05-2013, 02:25 AM
Replies: 73
Views: 9,788
Posted By hyltaiwan

RE: Saito FG-57 Cam gear positioning; How to do?

1.The cam gear with dot only is for the reqular cylinder (intake and exchaust magnaged as a single cylinder engine)
2.The cam gear with dot and slot is for the other cylinder (intake and exchaust...
Forum: RC Warbirds and Warplanes
10-08-2012, 01:04 AM
Replies: 1,032
Views: 162,641
Posted By hyltaiwan

RE: Top Flite Giant P47 arf IS coming

Here is the answer
http://www.youtube.com/watch?v=VizuGbSPPPo&feature=relmfu

And the engine is SAITO FG-57T
Forum: RC Warbirds and Warplanes
10-25-2011, 10:47 PM
Replies: 4
Views: 652
Posted By hyltaiwan

ZERO

http://youtu.be/fJhQN-27_LM

It is old but it is fun.
Forum: Gas Engines
05-12-2011, 01:24 AM
Replies: 1,358
Views: 232,662
Posted By hyltaiwan

RE: GAS Saito

Check fuel nipple on the carbulator. If it leaks, it is hard to observe.
Forum: Gas Engines
09-16-2010, 01:34 AM
Replies: 1,824
Views: 342,155
Posted By hyltaiwan

RE: Saito FG-20 or 21

I found that MAXIMA Formula K2 (USA) probably is the best lube for SAITO FG ,after nearly 10 different lube had been tried.
You can try it, if you were not so sure about your lube.
Forum: Gas Engines
08-30-2010, 04:08 AM
Replies: 5
Views: 1,068
Posted By hyltaiwan

RE: Saito FG advice requested

Try this, detach fuel nipple on carburetor. Apply some liquid gasket on the thread and reinstall it.

If it leaks, it will be very difficult to observe.
Forum: Gas Engines
07-11-2010, 10:58 PM
Replies: 300
Views: 81,086
Posted By hyltaiwan

RE: Saito - Pro FG 14 Tips and tricks only!!!

Steven's Fg14 has been running about 6 hours (2-2.5 hours on test stand + 15 x 10 minute flights on Me109 and 15 x10 flights on spitfire).

He was using orignial CDI on test stand and the frist...
Forum: Gas Engines
01-16-2010, 12:22 AM
Replies: 1,824
Views: 342,155
Posted By hyltaiwan

RE: Saito FG-20 or 21

If your FG20 is still on the test stand, I suggest you change to side mounted.(main needle point to the sky)
It is the best position for air to escape from the pump(if you ever disassembly the...
Forum: Gas Engines
01-13-2010, 11:39 PM
Replies: 1,824
Views: 342,155
Posted By hyltaiwan

RE: Saito FG-20 or 21

http://www.youtube.com/watch?v=q72A7muYmyY&feature=player_embedded#

This FG20 seems running pretty good after 5 hours' break in.

...
Showing results 1 to 25 of 30
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.