RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: al010964
Showing results 1 to 16 of 16
Search took 0.23 seconds.
Forum: RC Jets
11-15-2017, 06:01 AM
Replies: 2,111
Views: 485,444
Posted By al010964

Hi ZB, Can you advise if there is an issue with...

Hi ZB,
Can you advise if there is an issue with one of the tests, as in this post it sounds like the test is through but in one of your more recent posts you mention a 72 hour period and hopefully a...
Forum: Gas Engines
05-07-2012, 03:35 AM
Replies: 5
Views: 1,362
Posted By al010964

RE: Ignition Modules

Thanks W8ye,<div>
</div><div>Gave it go, didn't work unfortunately - will have to wait until I get my tools and change the ends over.</div><div>
</div><div>Cheers,</div><div>Adrian</div><div>...
Forum: Gas Engines
05-04-2012, 11:25 PM
Replies: 5
Views: 1,362
Posted By al010964

RE: Ignition Modules

Hi All,<div>
</div><div>On a (kind of?) related question, I am changing my OS GT55 ignition over to the rcexl 30 unit.</div><div>
</div><div>I think that i have the second generation rcexl unit...
12-03-2011, 01:23 AM
Replies: 5,152
Views: 1,349,837
Posted By al010964

RE: MOKI RADIAL Care and Maintenence

Hi All,

I would like to CNC up a mount for the Moki 250, just wondering if any one has an accurate drawing of the back mounting plate.

I have done a pretty good search of the forum and couldn't...
12-17-2010, 03:39 AM
Replies: 6
Views: 1,355
Posted By al010964

RE: VAC BAGGING LEADING EDGES ??

I have done this with Carbon, cut a strip about 1 inch (depending on LE) and then run this down the leading edge and around the tip.

With the carbon, i wanted a gloss finish; so was pretty...
10-11-2010, 03:58 AM
Replies: 8
Views: 6,973
Posted By al010964

RE: Kevlar Hinge

Hi All,

Thank you for your responses - i have ditched the idea of using the unidirectional kevlar. I hope to avoid using the a balsa wood / foam sandwich and get away with using the carbon.

By...
10-06-2010, 08:27 AM
Replies: 8
Views: 6,973
Posted By al010964

RE: Kevlar Hinge

Hi Dave,

Just to clarify - I am using a blue foam core wing and then covering with Kevlar (just the hinge area top and bottom to the trailing edge say a 2-3" band of kevlar). I am then adding the...
10-06-2010, 06:49 AM
Replies: 8
Views: 6,973
Posted By al010964

Kevlar Hinge

Hi All,

Hi I am new to bagging wings and have some questions re: kevlar hinges, and have searched the forums, without much luck.

(a) One of the main composite suppliers in the States sells a...
09-25-2010, 06:07 AM
Replies: 5
Views: 1,420
Posted By al010964

RE: ACP AUTO-VAC System

Hi All,

Just to close this off - have received a new pump and it works a treat.

Cheers,
Adrian
09-14-2010, 03:14 AM
Replies: 5
Views: 1,420
Posted By al010964

RE: ACP AUTO-VAC System

Hi Sunnybreeze,

Yep 50Mhz is correct for the 230V version - thank you for highlighting it.

Just an update to say that Ihave contacted ACP and their after sales service has been EXCELLENT!!...
09-05-2010, 01:47 AM
Replies: 5
Views: 1,420
Posted By al010964

RE: ACP AUTO-VAC System

Hi Sunnybreeze - we are 50Hz in Australia.

Cheers,
Adrian
09-04-2010, 04:21 AM
Replies: 5
Views: 1,420
Posted By al010964

ACP AUTO-VAC System

Hi All,

I have recently just purchased the 230v ACP Auto-Vac System and was having a go at my first part.

I was able to suck the bag down, and after a while the motor kicked in due to a drop in...
04-04-2010, 07:55 PM
Replies: 2
Views: 904
Posted By al010964

RE: JR PCM9X II & Hitec - Dual Channel Problem

ahhh. ..... I assumed that it could be done through the programmer without touching the TX endpoints; thanks for the advice

Cheers,
.adrian
04-04-2010, 03:38 AM
Replies: 2
Views: 904
Posted By al010964

JR PCM9X II & Hitec - Dual Channel Problem

Hi All -

I am having a problem setting up the Elevators on a Formula 3D. I am currently using Hitech hS-5645MG servo's, RS77S JR Receiver and PCM9X II Transmitter. I have set up the center and...
10-19-2009, 02:46 AM
Replies: 3
Views: 594
Posted By al010964

RE: Painting ARF - Surfaces with Clear Coat

Hi Jazzy - the grease that i am using would pass for vasoline, the problem is that any hint of the stuff near where you don't want it , and you get fish eye's (with the clear coat)...... it does work...
10-18-2009, 06:57 AM
Replies: 3
Views: 594
Posted By al010964

Painting ARF - Surfaces with Clear Coat

Hi - I am wanting to paint an arf wing and tail with clear coat; however I don't want to have the CA hinges stick. I have used a thick grease in the past to cover the hinges before painting but this...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.