RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 7
1
2
3
Last »
Search: Posts Made By: blindfly
Showing results 1 to 25 of 159
Search took 0.70 seconds.
Forum: Gas Engines
03-02-2006, 04:03 AM
Replies: 5
Views: 709
Posted By blindfly

RE: need RPMs for 3W-75

thank you, yes i am aware of all that and will proceed with care.
the engine ran fine so far but i really feel it needs some leaning.
i believe i should get around 6500 on max and 1500 on idle,
...
Forum: Gas Engines
03-01-2006, 03:26 PM
Replies: 5
Views: 709
Posted By blindfly

RE: need RPMs for 3W-75

don't know yet.
just bought the tach and was looking for some numbers to know what to expect.
i am just finishing the brake in and its time to start leaning out and dont want to over do it
so i...
Forum: Gas Engines
03-01-2006, 09:05 AM
Replies: 5
Views: 709
Posted By blindfly

need RPMs for 3W-75

just bought a tach and need some numbers...

its a 3W-75 i, rear intake, spinning 24x10 wood, also 3w.

anyone got RPMs for full and idle?

I think I'm on the rich side on both and want...
Forum: Giant Scale Aircraft - 3D & Aerobatic
02-19-2006, 02:57 PM
Replies: 6
Views: 1,067
Posted By blindfly

RE: aluminum?!?

LOL!!!!!!

man, where was your camera?!?

i cant believe people actually signed up for it, though i would....

well, it only happened to me once so...i guess i'm not good enough to...
Forum: Giant Scale Aircraft - 3D & Aerobatic
02-19-2006, 02:20 PM
Replies: 6
Views: 1,067
Posted By blindfly

aluminum?!?

hi all,

anyone here knows if the aluminum marked 6063 is close enough to the 6061 we get in most big planes?
I know its suposed to be a bit more flexible, but dont know to what extend.
can I...
Forum: Giant Scale Aircraft - 3D & Aerobatic
02-16-2006, 08:17 AM
Replies: 2,653
Views: 236,877
Posted By blindfly

RE: Aviation Models 33% Yak Build Thread

im afraid it would be cutting it a bit close from the down side of it.
maybe i'll get 2 new 8611...
what would be better:

a) 2 8611a for elevators and 4 9541 for the ailrons (2 ea.) (hmm,...
Forum: Giant Scale Aircraft - 3D & Aerobatic
02-16-2006, 06:57 AM
Replies: 2,653
Views: 236,877
Posted By blindfly

RE: Aviation Models 33% Yak Build Thread

hi all,

will the futaba 9451, (rated 120 oz i think) be enough for the surfaces?
other than the rudder (will use 8611a)...
Forum: Giant Scale Aircraft - 3D & Aerobatic
01-16-2006, 08:50 AM
Replies: 851
Views: 100,908
Posted By blindfly

RE: Aero-Works 50cc Yak

how will a 3w-75 fit on it??
Forum: Glow Engines
12-19-2005, 06:35 PM
Replies: 3
Views: 588
Posted By blindfly

RE: how do i check a perry before installing?

yes i am aware of that, i can do that by connecting a small manual ballon pump to the line i guess,

the question is - is it supposed to draw fuel if i do that? and if it does,
is that a good...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
12-19-2005, 06:31 PM
Replies: 2
Views: 600
Posted By blindfly

does anyone at HITEC read the mail !?

i have sent you guys 2 e-mails with no reply[:o]

i do not wish to adress the issues publicly on the porum but if that is your chosen way of communication...
Forum: Glow Engines
12-19-2005, 06:00 PM
Replies: 3
Views: 588
Posted By blindfly

how do i check a perry before installing?

hello all,

I got an old perry vp-30 i want to check before installing on the plane (and tapping the engine),

how do i do it?
where do i get pressure to turn it?

if i plumb it through...
Forum: Gas Engines
07-27-2005, 02:20 PM
Replies: 7
Views: 697
Posted By blindfly

RE: Sheared prop bolts help

Can someone please explain to me in words that a child (israeli one) would understand what exactly is the meaning of "bottomed out"?
does it mean that the bolts are all the way in the hub? (this is...
Forum: Giant Scale Aircraft - 3D & Aerobatic
07-24-2005, 04:53 PM
Replies: 0
Views: 285
Posted By blindfly

who has QQ 72'' yak?

thinking of getting one and wanted to know whats servos needed,
and if there is a gas engine setup for this one?

thanks
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
07-19-2005, 07:50 AM
Replies: 5
Views: 620
Posted By blindfly

RE: stupid mistake!! what to do????

yes its a metal gear.
TLH101 the dremel is a good idea, i'll do that.

hope it works,

thanks
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
07-19-2005, 05:42 AM
Replies: 5
Views: 620
Posted By blindfly

stupid mistake!! what to do????

it appears i put too much locktite on my servo head bolt and it wont come out.
being a staburn ***** that i am - i tried to force it and killed the screwdrivers slot in the bolts head, so now it...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
07-18-2005, 07:31 AM
Replies: 1
Views: 435
Posted By blindfly

dual elv. matching w/o programmer

O.K. i have been trying to do it right for some time now, with only small success.

i need step-by-step instructions on how to match the 2 elevators (2 servos), futabas, no programmer. mechanic...
Forum: The Clubhouse
07-17-2005, 07:22 AM
Replies: 11
Views: 13,361
Posted By blindfly

RC SHOP IN BANGKOK?

HEY ALL,
AS IM HEADING EAST FOR VECATION, I WOULD LIKE TO KNOW IF ANYONE KNOWS OF A RC SHOP IN BANGKOK OR THAILAND?
I CAN ONLY ASSUME PRICES WILL BE LOWER.. HA HA...

ANY INFO WOULD BE GREAT
Forum: Giant Scale Aircraft - 3D & Aerobatic
07-13-2005, 09:55 AM
Replies: 15
Views: 1,533
Posted By blindfly

RE: pull-pull setup (again, sorry)

sillyness, you were right on the money, thanks alot.
and finally an explenation i could understand (for why offset is needed for symetrical setup).
Forum: Giant Scale Aircraft - 3D & Aerobatic
07-12-2005, 09:36 AM
Replies: 15
Views: 1,533
Posted By blindfly

RE: pull-pull setup (again, sorry)

yes, i read it before,
but that example B is talking about differend arm lengths in servo and in rudder, so - not the case.


as much as i try to think about it i can't figure why will i need...
Forum: Giant Scale Aircraft - 3D & Aerobatic
07-12-2005, 08:57 AM
Replies: 15
Views: 1,533
Posted By blindfly

pull-pull setup (again, sorry)

Sorry to bring it up again. i know it's been beaten to death here but still, (i looked everywhere and read everything)...

i have my cables crossed, servo arm straight (no offset), rudder horns...
Forum: OMP - Ohio Model Products Support Forum
06-27-2005, 02:21 PM
Replies: 1
Views: 473
Posted By blindfly

80'' edge (MOAP)- no foam fuse???

Hi,

are there any kits sold without the foam core for the fuse?
i have a friend who wants to trade it but his fuselage is buildup and not foam,

he sais thats how he got it and the...
Forum: Glow Engines
06-16-2005, 06:56 AM
Replies: 5
Views: 732
Posted By blindfly

is my 46fx going to die????

my not so old OS 46 tx started to make a strange noise lately.
it sounds like a metal part klicking/knocking/banging. its not always there, but i couldnt find a specific rpm of engine anglr that...
Forum: Gas Engines
06-14-2005, 08:22 AM
Replies: 5
Views: 714
Posted By blindfly

fuel line??

i read it here somewhere that the vent line going out the bottom should first go around the tank,
or loop it or otself, or something like that.

does it really have to to this? if so -why?!?
...
Forum: Gas Engines
06-08-2005, 04:36 PM
Replies: 16
Views: 1,404
Posted By blindfly

RE: left-handed people

nice to see all the different approaches.
today i started it from the back for the first time, but it was on a bench, real easy!!

will try to do the same with the plane
Forum: Gas Engines
06-08-2005, 05:22 AM
Replies: 0
Views: 509
Posted By blindfly

TEXACO OIL?

ANYBODY KNOW IF THIS BRAND IS ANY GOOD FOR BREAK IN?
I USE THE TEXACO MOTEX 2T (FOR MOTORCICLES AND LAWNMOWERS),

I ASSUME ITS MINERAL SINCE IT DOESN'T SAY "SINTHETIC" AS OTHERS.

(B.T.W....
Showing results 1 to 25 of 159
 
Page 1 of 7
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.