RCU Forums - Search Results

Search: Posts Made By: M3blueGsr

Showing results 1 to 10 of 10
Search took 0.21 seconds.

Forum: E-Flite Helicopters

11-03-2011, 01:59 PM

Replies: 2

120SR = Mr. Bobble head

Views: 512

Posted By M3blueGsr

RE: 120SR = Mr. Bobble head

The rpm issue sounds like the battery has lost its punch. I have a bit of a wobble too which leads me to believe it is normal. You can always check the main shaft and the flybar.

Forum: E-Flite Helicopters

10-25-2011, 02:59 PM

Replies: 7

Blade 450 RTF??

Views: 1,725

Posted By M3blueGsr

RE: Blade 450 RTF??

If I have the old Dx6i what do Ienter for for the bold values? Idont have those in the controller I believe.. Do I just enter the non bold values and it will be fine? Or do I have to change...

Forum: Speed - RC Nitro Boats

06-05-2011, 01:27 PM

Replies: 1,587

Aquacraft Super-Vee 27 Nitro.

Views: 204,453

Posted By M3blueGsr

RE: Aquacraft Super-Vee 27 Nitro.

Does anyone know where to get a new starter shaft for the .18? I believe this is the part number: AQUG5721. I stripped mine and need a replacement.. Are there any other shafts that will fit this...

Forum: Speed - Electric

02-13-2011, 03:19 PM

Replies: 43

Making a RC boat

Views: 3,835

Posted By M3blueGsr

RE: Making a RC boat

Heres a 32 in cat.. might be too advanced..

http://www.rcgroups.com/forums/showthread.php?t=1347832

A rigger is pretty straight forward.. but they require flat water.. but they are fast..
...

Forum: Speed - Electric

02-13-2011, 01:20 PM

Replies: 43

Making a RC boat

Views: 3,835

Posted By M3blueGsr

RE: Making a RC boat

I would rebuild using some plans.. I dont think the design of that boat would work very well.

Forum: Speed - Electric

12-30-2010, 11:10 AM

Replies: 10

Built a rigger, Need advice with setup..

Views: 865

Posted By M3blueGsr

RE: Built a rigger, Need advice with setup..

This one I based off a jae .12. I'll probably start picking up the hardware and make it a nitro, and start from scratch for a brushless one.

Forum: Speed - Electric

12-29-2010, 06:48 PM

Replies: 10

Built a rigger, Need advice with setup..

Views: 865

Posted By M3blueGsr

RE: Built a rigger, Need advice with setup..

Hrmm ok those are pretty big.. I'll just have to start from scratch once I purchase all the electronics. I'd also like to make it a little better looking than a box with two sponsons. Maybe I'll do a...

Forum: Speed - Electric

12-29-2010, 06:19 PM

Replies: 10

Built a rigger, Need advice with setup..

Views: 865

Posted By M3blueGsr

RE: Built a rigger, Need advice with setup..

Yes it goes through the hull, I have 4-3/4" longx 1-3/4" high.. from the rear boom to the seperation to the rear compartment. In front of that is 4-1/4" to the nose which is sealed. The lower Kv I...

Forum: Speed - Electric

12-29-2010, 05:54 PM

Replies: 10

Built a rigger, Need advice with setup..

Views: 865

Posted By M3blueGsr

RE: Built a rigger, Need advice with setup..

Thanks for the fast reply,Ihave about 16 inches from the trailing edge of the sponson, to the rear tub. There are two compartments that are 2-3/8ths wide x 8" for the rear most compartment and...

Forum: Speed - Electric

12-29-2010, 04:50 PM

Replies: 10

Built a rigger, Need advice with setup..

Views: 865

Posted By M3blueGsr

Built a rigger, Need advice with setup..

So last winter I built a rigger and was planning on going with a nitro setup, but changed my mind and want to go brushless. The overall lenth of the rigger is 26" without the drive hardware. I read...

Showing results 1 to 10 of 10