RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: crownline
Showing results 1 to 11 of 11
Search took 0.21 seconds.
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-25-2013, 02:38 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Richard Have you made anymore progress with...

Richard
Have you made anymore progress with your modifications. i'm interested to see where the final weight will come in at .

Steve
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-25-2013, 09:07 AM
Replies: 2,259
Views: 493,252
Posted By crownline

After reading what I wrote , I see my brain and...

After reading what I wrote , I see my brain and my one finger typing method did not keep up ( LOL )
I wanted to say the Moki's have Low RPM's but HIGH torque .
I just don't know if the offset in...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-24-2013, 09:45 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Steve

Steve
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-22-2013, 01:52 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Richard Thanks for the info on the Dihedral, I...

Richard
Thanks for the info on the Dihedral, I need to reduce it a bit on mine, after checking it again it is at 7Deg on both sides . not sure how much difference it makes but will do it anyway.
...
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-16-2013, 08:02 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Chris i agree with you a lower approach would...

Chris
i agree with you a lower approach would be better, with the motor having very little time on it ( 10 min ) i wanted to stay a litter higher i case it quit on me. besides IMAC = 7years Gee...
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-15-2013, 08:32 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Jaz Your right i have more than i should, it's...

Jaz
Your right i have more than i should, it's about 6-1/4 Deg. i need to adjust the flying wires. i though i read on this thread it should be 4-1/2 to 5 is that correct ?

Steve
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-15-2013, 07:20 PM
Replies: 2,259
Views: 493,252
Posted By crownline

This is my test flight on Sunday, keep the...

This is my test flight on Sunday, keep the laughter to a minimum ( especially when i try to land it . )

Steve


http://youtu.be/QCe8g81L0l0
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-14-2013, 02:07 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Well I had a successful maiden flight yesterday...

Well I had a successful maiden flight yesterday !!! I think my hart is still racing, that airplane sure burns up a lot of sky in a hurry.
I sure love the sound of that Moki 215 at times it was...
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-12-2013, 08:17 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Chris Great job today !! i hope mine turns...

Chris
Great job today !!
i hope mine turns out as good as yours did. going for it tomorrow weather permitting.

Steve
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-05-2013, 08:54 PM
Replies: 2,259
Views: 493,252
Posted By crownline

No maiden today, got to the field , range checked...

No maiden today, got to the field , range checked , fueled up , shot of whiskey to calm the nerves , checked batteries and the ignition battery was dead. i ran the motor last night
and with no...
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-04-2013, 08:47 PM
Replies: 2,259
Views: 493,252
Posted By crownline

Well it looks like i have been stalling long...

Well it looks like i have been stalling long enough, time to maiden mine tomorrow ( gulp ).
i hope i'm am as successful as everyone else. fired up the Moki 215 today ( i think just to listen to it )...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.