RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: hou_zhenyu
Showing results 1 to 14 of 14
Search took 0.16 seconds.
Forum: Electric Pattern Aircraft
10-31-2012, 07:42 PM
Replies: 6
Views: 1,975
Posted By hou_zhenyu

RE: Hacker Q80 14xs + CC HV80 doesn't work

Hi, Mike

Are the customers using the exact same combo, Q80 14xs + CCHV80 Ice? If yes,can you help to share the settings? Especially the timing, the PWM, startup power and Throttle response. And...
Forum: Electric Pattern Aircraft
10-31-2012, 01:53 AM
Replies: 6
Views: 1,975
Posted By hou_zhenyu

Hacker Q80 14xs + CC HV80 doesn't work

Hi,

Has anybody used the combination Hacker Q80 14XS and CC HV80 V2.

I tried this with almost all the setting, timing from 0 to 9, set PWM to 8, 16, "out-runner mode", the motor is either...
Forum: RC Pattern Flying
06-18-2012, 05:54 PM
Replies: 31
Views: 6,716
Posted By hou_zhenyu

RE: TALON EXTREME by Randy Hicks Designs

What's the hole behind the canopy used for?
Forum: RC Pattern Flying
09-28-2011, 10:12 PM
Replies: 18
Views: 1,664
Posted By hou_zhenyu

RE: YS70

However, in the manual of YSFZ70S, it said

"Then installing the came gear, the side with a point mark should be facing the opening of the gear box. Note that is should also be mounted with the...
Forum: JR Radio & Spektrum Radios
08-21-2011, 05:43 AM
Replies: 2
Views: 758
Posted By hou_zhenyu

Does JR DS331 has rubber grommets and eyelets

Hi,

I just brought a JRDS331 mini servo -http://www.jrpropo.co.jp/english/products/propo/details.php?hen=02154&db_flg=eng_db1(note that it'sNOT JRNES 331) - as the throttle servo for a .90...
Forum: Glow Engines
07-06-2011, 04:22 AM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Continued tunning the engine in the last weekend, still, the HSV is tuned to have high rpm at somewhere between 2.5 to 3 turns. Have several dead sticks in the air and figured out later that caused...
Forum: Glow Engines
06-20-2011, 11:38 PM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Failed to tune the engine yesterday as i brought the wrong fuel to the field :(, .

I don't know if the pressure can be held, as I drained the fuel immediately after running.
and I'm sure the...
Forum: Glow Engines
06-18-2011, 04:15 AM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Continued tuning the engine after two busy weekends, before started the engine, I
1. tightened the muffler
2. tightened the valve-cover bolts
3. a new glow plug

however, the engine is still...
Forum: Glow Engines
05-30-2011, 07:15 PM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Two more things
1. Make it clear, the feul is leaking from the place inside the red...
Forum: Glow Engines
05-30-2011, 06:49 PM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Thanks all of your information, very helpful.
Here are some latest updates:
1. Continued to break in the engine with RPM about 7000 for a full tank (420cc)
2. Tried to adjust the HS needle, RPM is...
Forum: Glow Engines
05-29-2011, 05:43 PM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

This is all about break-in from the instruction manual:

"BREAK-IN
To maximize engine performance and increase durability, please
follow this break-in procedure:
1. Use the same size (or...
Forum: Glow Engines
05-29-2011, 07:18 AM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

I continue break-in the engine today and i did use a tachometer, after 4 tanks run. Istart to tune the high speed and butit's still quite strange, it's hard to find out the high RPM, when HSN is...
Forum: Glow Engines
05-28-2011, 03:34 PM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

RE: YS FZ115S break-in questions

Thanks a lot for you answer, much more confident to continue the break-in.

One more question, "insensitive needle setting with big propellers" problem is specific to YS engine, or it's for all...
Forum: Glow Engines
05-28-2011, 06:39 AM
Replies: 21
Views: 4,408
Posted By hou_zhenyu

YS FZ115S break-in questions

Hi, Everyone<div></div><div>I'm breaking in a YS-FZ115S engine, following the instructions at http://www.geistware.com/rcmodeling/glowpower/ys_engines.htm#Break-in (the manual is just too...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.