RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mhols
Showing results 1 to 19 of 19
Search took 0.64 seconds.
Forum: Speed - RC Nitro Boats
04-15-2005, 05:28 PM
Replies: 1
Views: 536
Posted By mhols

RE: Engine questions (picture)

I got a bunch of new and some used parts for the OPS 60 engine
i got headers (long and short type).exhaust gaskets,sylinder head gaskets,cranks.piston and sleeve.head buttons.
Forum: RC Boats General Discussion
04-15-2005, 04:43 PM
Replies: 2
Views: 376
Posted By mhols

RE: Need prop recomendation.

try a Prather prop ss 230 or ss 235 depending on the nitro % that you are planing to use (you must sharpen and balance these prop as with any props) these OS engines runs great on 40% nitro and with...
Forum: Speed - RC Nitro Boats
04-15-2005, 04:31 PM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

Hi Jeff
no what is PM

Martin
Forum: Speed - RC Nitro Boats
04-15-2005, 03:19 PM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

here are some more photos
Forum: Speed - RC Nitro Boats
04-14-2005, 04:06 PM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

I do have a new OPS carb i dont know what OPS engine its for but it fits your engine but you will have to modify the throttle arm.i am soon ready with the photos.
Forum: Speed - RC Nitro Boats
04-14-2005, 09:02 AM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

I will take some photos tonight. the back plate that i got is complete with rotor disc.O-ring seal for the carb and carb lock bolt with nut.
I also got a new red sylinder head .two pistons and...
Forum: Speed - RC Nitro Boats
04-14-2005, 06:07 AM
Replies: 3
Views: 619
Posted By mhols

RE: Whats the difference between nitro and gas?

the gas engine are more easy to start you only have to pull the starter handle. with nitro engies you need a hand held starter and a battery to glow the plugg.but you can also get nitro engines with...
Forum: Speed - RC Nitro Boats
04-14-2005, 05:56 AM
Replies: 2
Views: 672
Posted By mhols

RE: Nitro-Vee major problems

I have been building boats and raced them for nearly 10 years i got boats from 100 cm to 190 cm with engines from 10cc to 35 cc both nitro and gasoline. and the only hull thats good are those made...
Forum: Speed - RC Nitro Boats
04-12-2005, 05:33 PM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

I got these parts .do you have any photos taken from the carb side
Forum: Speed - RC Nitro Boats
04-07-2005, 05:27 PM
Replies: 5
Views: 686
Posted By mhols

RE: sc 61 engine

Just loosen the glow plug a few turns and when the engine starts just tighten it again.
from fully closed unscrew the needle 2-2 1/2 turn this is just a starting point you might to turn it in if...
Forum: Speed - RC Nitro Boats
04-07-2005, 04:53 PM
Replies: 2
Views: 435
Posted By mhols

RE: sc61 marine engine

from fully closed turn it 2 1/2 full turns out this is just as a staring point you may have to turn it in if it sound muddy.
Forum: Speed - RC Nitro Boats
04-07-2005, 04:49 PM
Replies: 2
Views: 435
Posted By mhols

RE: sc61 marine engine

just loosen the glow plug a couple of turns and when it starts tighten it again
Forum: Speed - RC Nitro Boats
04-07-2005, 04:43 PM
Replies: 3
Views: 968
Posted By mhols

RE: need prop help (nitro vee)

hello
The Prater 215 SS prop is a good prop for your boat and engine take a look at Prathers homepage i think this is their address PRATHER PRODUCTS INC.COM
Forum: Speed - RC Nitro Boats
04-07-2005, 04:11 PM
Replies: 17
Views: 2,838
Posted By mhols

RE: OPS .60 Parts

Hello Jeff

I got a bunch of new and used parts for the OPS 60 i got the same engine i my sons boat and a OPS 90 in mine.
i could see from your photos that your engine didnt got any water...
Forum: Glow Engines
04-07-2005, 03:56 PM
Replies: 2
Views: 652
Posted By mhols

RE: OPS missing parts

HELLO
I GOT A WHOLE BUNCH OF USED AND NEW OPS PARTS .
AND I GOT SEVERAL HEAD BUTTONS AND SYLINDER HEADS .
IF YOU GOT THE INSIDE DIA OF THE SYLINDER I CAN SEE IF I GOT THE PARTS U NEED.
Forum: RC Boats General Discussion
09-01-2003, 06:28 PM
Replies: 0
Views: 443
Posted By mhols

rotor disc for picco p80

ANYONE OUT THERE WHO GOT A ROTOR DISC FOR A OLDER picco p80
marine engine
i got some photos if anyone wants to see howe the disc looks
Forum: RC Boats General Discussion
06-13-2003, 09:24 PM
Replies: 11
Views: 906
Posted By mhols

K and B outboard

Hi Gary
i have run k/B OUTBOARDS FOR MANY YEARS and i still do
Both 3,5-11- 13 -16 ccm
try to keep the rpm low when you drop it on the water
i think its possible to get two types of cables to...
Forum: RC Boats General Discussion
05-14-2003, 07:15 PM
Replies: 23
Views: 3,426
Posted By mhols

Outboards on scarab

Hey
twin engnines is no problem on a deep wee
have a look on this homebuilt boat that i made last winter
it got two 11 ccm K/B outboards
its 160 ccm long and 42 ccm
so just go for it
Forum: RC Boats General Discussion
05-14-2003, 06:49 PM
Replies: 6
Views: 1,782
Posted By mhols

Need Old Picco P80 Marine Engine Parts

Hello you guys
i got this Picco p80 marine engine
i need the rotor valve and main needle badly
anyone who knows where to get these parts :)
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.