RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: jakobsladderz
Showing results 1 to 8 of 8
Search took 0.11 seconds.
Forum: Engine Conversions
12-01-2021, 03:54 AM
Replies: 8
Views: 2,725
Posted By jakobsladderz

Further Progress

A bit further on now - the engine is in the plane I want to power and I have gone through the fuel map (throttle x rpm => injector pulsewidth) and got it running pretty nice. It's still a little hard...
Forum: Engine Conversions
11-04-2021, 02:40 PM
Replies: 8
Views: 2,725
Posted By jakobsladderz

On the injector - I mounted it into the side of...

On the injector - I mounted it into the side of the intake tube so it runs across the back of the engine (parallel with the engine fins. I used a dremel to make a hole just big enough that the...
Forum: Engine Conversions
11-04-2021, 02:25 PM
Replies: 8
Views: 2,725
Posted By jakobsladderz

Initially I was planning to run the engine on...

Initially I was planning to run the engine on E85+Oil given that it's a bit greener and that there's a power advantage compared to straight Gas. Unfortunately, during the development work on the...
Forum: Engine Conversions
11-03-2021, 10:07 PM
Replies: 8
Views: 2,725
Posted By jakobsladderz

Efi

Thanks for the info on the carby mods - That would have been my next step..

In the end I have put together a fuel injection system for the engine and have it running well :).

The Fuel injector...
Forum: Engine Conversions
10-13-2021, 02:35 PM
Replies: 3
Views: 3,063
Posted By jakobsladderz

Did the engine run well with Glow ignition before...

Did the engine run well with Glow ignition before the CDI Conversion? I have converted a smaller ASP 4S to CDI and running on glow fuel it ran Ok (rich in the midrange, but it was anyway). It...
Forum: Turbine Clinic
09-08-2021, 07:00 AM
Replies: 2
Views: 3,344
Posted By jakobsladderz

Possibly wrong section but in any case, you...

Possibly wrong section but in any case, you should have no problem running a turbine fuel pump with a brushed motor using an ESC designed for brushed motors and a servo tester would work with that...
Forum: Engine Conversions
09-08-2021, 06:50 AM
Replies: 8
Views: 2,725
Posted By jakobsladderz

ASP FS61AR CDI Conversion - Q regarding Rich Midrange.

Hi,

I've been playing around with an ASP FS61AR of late. It was sitting for near on 10 years and needed a new set of bearings through it (and a couple of other parts) to make it new again given...
Forum: Futaba Radios Direct support forum
11-21-2011, 05:09 PM
Replies: 7
Views: 4,609
Posted By jakobsladderz

RE: Does Futaba sell replacement shell for the 9C?

I am in Australia and was wondering about a spare front panel and rear case for a 9CHP. The Aussie distributor is new to the business and I am having trouble getting assistance. I emailed the USsite...
Showing results 1 to 8 of 8


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.