RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: corn_tortilla
Showing results 1 to 11 of 11
Search took 0.61 seconds.
02-10-2004, 12:59 AM
Replies: 2
Views: 1,024
Posted By corn_tortilla

RE: caliber 30 4 stroke conversion

Don't know about the four stroke; but I though the OS32 was a bit underpowered. My .50 conversion kit should arrive Weds w/ an OS50 to accompany it. (But if you take this route make sure to...
02-10-2004, 12:57 AM
Replies: 3
Views: 530
Posted By corn_tortilla

RE: Airtronics RD8000 Swashplate Reversal??

You can also cheat and do a reverse your pitch curve.

Instead of Neg to High pitch being 0 - 100

Make your Neg to High pitch 100 - 0

It's Ghetto; but it works
12-31-2003, 02:42 AM
Replies: 45
Views: 33,444
Posted By corn_tortilla

RE: Caliber 30. 46-50 Engine conversion review.

So after test flying my scaler mechanics (.30 size upgraded to a .46), I'll be putting an upgrade kit on order too. I couldn't believe how fast that thing would skyrocket into the air and not bog...
11-30-2003, 02:46 PM
Replies: 8
Views: 1,083
Posted By corn_tortilla

RE: new Caliber coming

Setup is difficult in getting the controller to work right. Not in getting the chopper configured.... i had to swap my Aileron and Pitch Servos and reverse them too... As far as setting up the...
10-20-2003, 01:18 PM
Replies: 4
Views: 658
Posted By corn_tortilla

RE: Engine Loading!!!

Look into getting a header tank.... I think they're about $20-$25

i have the quick uk one
10-01-2003, 05:22 PM
Replies: 4
Views: 937
Posted By corn_tortilla

RE: Fine tuning OS32 with 20C carb

I finally got mine tuned; but it took some time for the recipe. These are the settings that I have setup.

+9 0 -9 Pitch
15% CoolerMaster Fuel
High End Needle 1 - 1 1/8
Low End Mix 20...
09-29-2003, 04:14 PM
Replies: 0
Views: 425
Posted By corn_tortilla

Can someone post Hawk dimensions

Can someone please post some of the hawk dimenions online and name your explicit model. Here is what I'd like to get.

A) Length from Tail to Nose of heli.
B) Lenght from Tail to Rotor Mast...
09-28-2003, 10:59 PM
Replies: 3
Views: 636
Posted By corn_tortilla

RE: Binding in the tail rotor of a Caliber 30

yes,

I took my zippo knife and shaved a little off the top and bottome of the 90 degree elbow (and the slot it goes in on both sides), it should be silky smooth with no resistance. It took me...
09-27-2003, 07:36 PM
Replies: 45
Views: 33,444
Posted By corn_tortilla

RE: Caliber 30. 46-50 Engine conversion review.

I'm curious as to why everyone put the 50 in it... If the 50 still overpowers the caliber when at +10 degree pitch, why don't you buy a .46. It's cheaper, you may not need a governor and your...
09-23-2003, 02:23 AM
Replies: 2
Views: 587
Posted By corn_tortilla

RE: New frame stiffeners for Cal. 30, any takers???

That seems pricey compared to the other fixes, I've seen.....
09-14-2003, 03:12 PM
Replies: 1
Views: 502
Posted By corn_tortilla

Radio + Gyro Setup Question

Hi,

I'm in the process of setting up my Caliber 30 heli, with a Airtronics RD8000, Futaba GY401 &9253 Servo. How do I connect the servo and gyro? The airtronics manual says to plug the...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.