RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: jpiraino
Showing results 1 to 19 of 19
Search took 0.64 seconds.
Forum: Beginners
04-11-2005, 09:52 AM
Replies: 32
Views: 3,793
Posted By jpiraino

RE: Best building surface.

I use a Dow Styrofoam board, that is available from a lumber yard. It is about 5/8" thick and comes in 4'x8' size. Make sure it is on a flat surface, like a 3'x6-8' folding table available at Sams...
Forum: S.P.A.D. Aircraft - Coroplast design
10-16-2004, 06:30 AM
Replies: 6
Views: 579
Posted By jpiraino

RE: Debonaire Wing Dihedral

No, I reinforced the wing root with a new gusset
Forum: S.P.A.D. Aircraft - Coroplast design
10-15-2004, 10:15 AM
Replies: 6
Views: 579
Posted By jpiraino

RE: Debonaire Wing Dihedral

Hi Fellows, appreciate the replies.
I had one wing covered, so I took out my backsaw, and sawed right down the middle of the two spars, and was able to re glue the spars at the proper angle. It...
Forum: S.P.A.D. Aircraft - Coroplast design
10-14-2004, 08:37 PM
Replies: 6
Views: 579
Posted By jpiraino

Debonaire Wing Dihedral

I may have made a mistake on the dihedral. I have 5" on both wings on the spars. Do you just use the 5" only, which would give you 2 1/2" on each wing tip?
Forum: Futaba Radios Direct support forum
08-11-2004, 08:19 AM
Replies: 2
Views: 480
Posted By jpiraino

6EXA programming help

What would you recommend for dual rates for a trainer beginner pilot. Also explain exponential settings and when to use them

Thanks
John
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-11-2004, 08:05 AM
Replies: 2
Views: 446
Posted By jpiraino

RE: Radio Retailer's ( which one will seperate)?

Go to Bruckner Hobbies out of NY. I just bought a Futaba 6EXA transmitter in any channel for $79.95
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-06-2004, 09:00 AM
Replies: 3
Views: 557
Posted By jpiraino

RE: 6axe futaba settings for trainer

As I understand, you have among other things dual/rates Hi and Lo that require a percentage setting. For a trainer what would you set for the low rate/hi rate. What about exponential settings
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-05-2004, 07:18 PM
Replies: 3
Views: 557
Posted By jpiraino

6axe futaba settings for trainer

Newbie wants to know what settings to put into Futaba 6aex for typical trainer?
Forum: Glow Engines
07-23-2004, 12:35 PM
Replies: 1
Views: 511
Posted By jpiraino

Not drawing Fuel

I have a GMS 47 installed in new plane. When I open throttle put finger over carb to draw fuel nothing happens. Checked Clunk and lines, can find nothing wrong. Will not start or sputter.
Forum: S.P.A.D. Aircraft - Coroplast design
07-01-2004, 07:48 PM
Replies: 5
Views: 978
Posted By jpiraino

RE: Where do I find American PVC Downspout Material

I just went to a local hardware store this afternoon, used to be an ACE...now independent talked to the buyer, she looked at her wholesalers catalog, and I found it. It listed an order quantity of 10...
Forum: S.P.A.D. Aircraft - Coroplast design
06-30-2004, 02:41 PM
Replies: 4
Views: 541
Posted By jpiraino

RE: SPAD3DT Throttle Servo Location

I was pondering my landing gear, then it dawned on me, I had an extra set of landing gear from a Sig 25 tail dragger....that's what I'm going to use
Forum: S.P.A.D. Aircraft - Coroplast design
06-30-2004, 02:25 PM
Replies: 13
Views: 991
Posted By jpiraino

RE: Cutting Aluminum Tube for Spa3DT.Methodology?

I used my craftsman band saw, with a fine tooth 1/4" blade, normally used to cut wood, worked great on tube. Haven't started on the servo holes yet.
Forum: Beginners
11-17-2003, 01:10 PM
Replies: 2
Views: 648
Posted By jpiraino

LT-25 or Sig Seniorita

What do you think would be a good plane for me. I have done some flying, but have had a few crack ups. Want to build either one. Your input.

Thanks
Forum: Kit Building
11-16-2003, 03:16 PM
Replies: 2
Views: 429
Posted By jpiraino

LT-25 or Seniorita

Which would you recommend, I have some flying experience

Thanks
Forum: ARF or RTF
11-03-2003, 10:14 AM
Replies: 1
Views: 493
Posted By jpiraino

Mecoa Easy Flyer 46 ARF

Has anyone built and flown a Mecoa 46 arf easy flyer....results?
Forum: S.P.A.D. Aircraft - Coroplast design
11-01-2003, 03:10 PM
Replies: 10
Views: 780
Posted By jpiraino

Tail Wheel for Spa3dt

I am building a Spa3dt, and am a little confused on the tail wheel. How does it swivel?
Thanks
Forum: Kit Building
10-30-2003, 07:56 PM
Replies: 18
Views: 2,237
Posted By jpiraino

RE: Questions on Sig Kits

Sig kits are the greatest, i have built the senorita...LT- 25...and the LT-40. They all were great flyers.
One other important thing is the service...They are very responsive to the modlers needs,...
Forum: Beginners
10-08-2003, 09:37 PM
Replies: 25
Views: 1,967
Posted By jpiraino

RE: LT 40 doesn't want to land

I want to thank all you fellows who helped me with some valuable information. I am getting the hang of landing by cutting back on the throttle earlier.
Also, I believe like most beginners that if...
Forum: Beginners
10-04-2003, 12:51 PM
Replies: 25
Views: 1,967
Posted By jpiraino

LT 40 doesn't want to land

Hi, I have an LT 40 ARF with an O.S. 40 LA. It is very difficult to land in a short distance, it just wants to glide. I have:
changed props...flying 10/6
balance is fine
cut idle...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.