RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: denzil
Showing results 1 to 14 of 14
Search took 0.63 seconds.
12-20-2008, 11:42 AM
Replies: 4
Views: 497
Posted By denzil

RE: blade 400 6100e aux 1 problem

that was it...thanks for your help......now for the rest of the set up...i'm sure there will be more questions
12-20-2008, 11:34 AM
Replies: 4
Views: 497
Posted By denzil

RE: blade 400 6100e aux 1 problem

thanks...I'll try that now.....
12-20-2008, 08:43 AM
Replies: 4
Views: 497
Posted By denzil

blade 400 6100e aux 1 problem

I just got a used blade 400. While checking it out I noticed the swash plate was tilted to the left after powering up. After further checking I noticed the lower of the 2 servos stacked behind the...
02-01-2006, 03:23 PM
Replies: 263
Views: 67,353
Posted By denzil

RE: Great Planes Super Sportster EP with Modified Power System

I have used the Hitec Laser 4 for a couple of years, with several planes, with no problems. I'm not any kinf of expert and have not had experince with Futaba so I cannot compare the two. I can...
01-17-2006, 01:50 PM
Replies: 263
Views: 67,353
Posted By denzil

RE: Great Planes Super Sportster EP with Modified Power System

David

It's amazing how similar my plane looked compared to the one in your picture.

I ordered a new plane and I think I'm going to take your advice on the ESC. Can't afford another shut...
01-16-2006, 12:04 PM
Replies: 263
Views: 67,353
Posted By denzil

RE: Great Planes Super Sportster EP with Modified Power System

I experienced a similar incident yesterday where I lost all power and crashed as a result. I was flying the S 600 GD sysytem using the 2.5:1 ratio with a 10x7 prop. I may have overloaded the system...
12-18-2005, 11:17 AM
Replies: 263
Views: 67,353
Posted By denzil

RE: Great Planes Super Sportster EP with Modified Power System

Try Maxamps.com for 3300mah and 3700 mah packs. I'm flying a stock set up with GP3700 pack in hump configuration. Seems to balance the same as with stock pack even though it is 4 oz heavier due to...
11-29-2005, 10:33 AM
Replies: 263
Views: 67,353
Posted By denzil

RE: Great Planes Super Sportster EP with Modified Power System

I noticed that several people are using 3300 mah packs in their Super Sportster. As these packs are heavier than the stock NICD pack and the plane is a little nose heavy with the stock pack I thought...
03-15-2005, 02:32 PM
Replies: 2
Views: 830
Posted By denzil

Hummingbird V3 tail motor

Mine wants to rotate left even with the gyro all the way up. Its manageable but requires almost constant right rudder input. More as the battery wears down. Would the high authority tail motor help?...
02-24-2005, 10:24 AM
Replies: 2
Views: 529
Posted By denzil

RE: Hummingbird v3 wants to rotate to left

There is only one adjustment on the gyro. I didn't see any adjustment on the mixer but I'll look closer just in case. Thanks for the input.
02-23-2005, 11:17 AM
Replies: 2
Views: 529
Posted By denzil

Hummingbird v3 wants to rotate to left

I have a Hummingbird v3. I have the gyro gain all the way to the right(clockwise) and still have to slide my trim approx 1/2 way to he right to keep it from wanting to rotate to the left. I notice as...
02-12-2005, 08:55 PM
Replies: 5
Views: 646
Posted By denzil

RE: Hummingbird v3 gyro function

Thanks for the input. I kept trying and seem to have gotten things working better. Now the rotation is minimal. I find if I get out of the ground effect the rotation slows down to almost nothing. It...
02-11-2005, 01:45 PM
Replies: 5
Views: 646
Posted By denzil

Hummingbird v3 gyro function

I have a Hummingbird v3. I am curious as to what I should expect assuming the helicopter is set up properly. Should the gyro keep the helicopter from rotating on its own or does it just slow it down....
02-08-2005, 03:16 PM
Replies: 2
Views: 532
Posted By denzil

RE: Hummingbird v3 how to take off rotor head?

I just happened to have to do that last night after a minor mishap. Yes, pull the metal pin and slide off the main shaft.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.