RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: c016Y
Showing results 1 to 25 of 215
Search took 0.72 seconds.
10-14-2006, 03:23 AM
Replies: 10
Views: 1,924
Posted By c016Y

RE: 36% KATANA BALANCE POINT?

I ran out of money on my project and will probably be looking to sell this pretty cheap (AW 36% Kat).. where would you list something like this? How the heck could you mail it!!! I imagine that...
Forum: 3D Flying!
03-24-2006, 01:39 PM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

I forgot to put on my post about how I fly... I could see why you think I fly fast/hard etc. I never flew the ucd fast on that first plane. I was always too scared to do that. The only time I...
Forum: 3D Flying!
03-24-2006, 01:12 PM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

A little late weighing in here, but, I started out running ds811's all around. First the rudder started fluttering around nutral when you flicked the stick... kind of the crazy violent shaking...
Forum: 3D Flying!
02-19-2006, 05:22 PM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

barry.. that is exactly what i was looking for.. so the sa 125 is pretty equal to the ys 1.10. I wouldl likely need to throw on a cline reg or perry pump neither of which I have ever needed to used...
Forum: 3D Flying!
02-17-2006, 11:29 AM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

Accoding to saito the 150 will swing a 16x8 @9000 rpms? If this is right that should be stronger than a ys 1.10 right? That is about what I was getting out of my 16x6. The 120 15x8 at 9000 and the...
Forum: 3D Flying!
02-17-2006, 10:20 AM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

Has anyone flown or know of anyone that has flown this plane with the saito 120? I have always had the ys 1.10, but, lost elevator control at about 200 ft up (screws came out of servo arms on...
Forum: 3D Flying!
01-17-2006, 10:39 AM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

Are you asking if you can use rubber bands to set the wing on the bottom of the plane? The answer is you don't. That is a bad design and a hassle anyways. The bolts are easier. The 2 bolts is a...
01-16-2006, 02:23 AM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

I actually got the yak, but, am guessing this portion is the same. It has these zbend clevis that you have to put the cf rods through. The stinking rods don't fit. Anybody else have this problem? ...
Forum: 3D Flying!
01-11-2006, 02:14 PM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

Where is your cg?
12-28-2005, 10:12 PM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

Where can I find a beam mount for my hacker a20 motor? Something like this:
http://image.rcuniverse.com/forum/upfiles/57969/Nl30127.jpg

Or ... is there a better way to mount this engine?
11-18-2005, 04:06 PM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

Great info.. thanks tman
11-18-2005, 03:11 PM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

I am no 3d master either.. got pretty good at harriers with my ucd .60 and even rolling harriers. That plane is crashed and got a f90.. anyways..

I am hoping this plane will make me a better...
11-18-2005, 02:08 PM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

I hope I am not making a mistake getting the yak (flex like the ucd). I am not a beginner at all. I just have not done electric however. I am looking for something fun that can do 3d in the...
11-18-2005, 12:39 PM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

By chance could you provide me with a link to a good battery. Would be nice to be at tower since family is looking to by this for christmas and they know that site.. if not.. anywhere. Thanks so...
11-18-2005, 03:22 AM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

I am actually looking at the yak, but, have seen some good recommendations on power plant on this forum. I think ucd is about the same weight. Is this engine and esc good?
A20-22L w/Hacker X-20...
11-15-2005, 11:30 AM
Replies: 94
Views: 10,305
Posted By c016Y

RE: Aeroworks 36% Katana

I bought the AI 3w 106 b2 used and this is my first large scale project. Just curious how you mounted that engine and if you could give me any pointers on engine installation, measurements, standoff...
11-09-2005, 02:53 PM
Replies: 94
Views: 10,305
Posted By c016Y

RE: Aeroworks 36% Katana

I thought you might have been a bit tail heavy causing extra coupling, but, do you remember what % you ended up with rudder->elev?

Also curious you mentioned you used CF wing tubes? How did you...
11-09-2005, 02:43 PM
Replies: 94
Views: 10,305
Posted By c016Y

RE: Aeroworks 36% Katana

Wanted to climb when inverted using rudder? Does that mean it had some pretty harsh pitch coupling to the belly in ke?
11-09-2005, 01:37 AM
Replies: 16
Views: 2,215
Posted By c016Y

RE: Great Planes...YAK 55 "EP"! Brand New! Pic

yup.. there are a lot out there. Just really curous about this one. I like the idea of maybe some extra crash protection.
11-09-2005, 01:26 AM
Replies: 16
Views: 2,215
Posted By c016Y

RE: Great Planes...YAK 55 "EP"! Brand New! Pic

Anyone willing to share their experience actually flying this plane and what setup they used. I am thinking about getting it. Looked at the ucd, but, I hear is has the same nasty coupling that the...
11-08-2005, 04:04 AM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

ok.. i am thinking about getting one of these or a yak 55 ep. Curious on flight reports.. do they 3d well. harriers, inv harriers, flat spins, asc flat, hover, ke coupling? (how bad). Any...
11-08-2005, 03:11 AM
Replies: 543
Views: 61,077
Posted By c016Y

RE: U-Can-Do 3D EP Anyone seen it yet?

can you send me an email with your video? I can host it one tulsa3d.com and I would like to see it.
09-14-2005, 09:29 AM
Replies: 109
Views: 12,863
Posted By c016Y

RE: TOC1 Yak 54

I just wanted to respond to several posts in this thread about the fact that this company uses domainsbyproxy to "hide" their identity. Domainsbyproxy allows you to do name registration w/o posting...
09-01-2005, 02:05 AM
Replies: 6
Views: 1,579
Posted By c016Y

RE: Katana s 36%

That is a great video. Not sure about the music.. I like the engine sound much better.. that would have been music to my ears!! ha.. jj. I am getting really excited to get this thing up!! Thanks...
Forum: 3D Flying!
08-30-2005, 08:58 PM
Replies: 3,517
Views: 437,158
Posted By c016Y

RE: U Can Do 3D

No.. didn't say the radio was what made you good. It is all in the shoes actually. I find that no shoes makes my ucd fly much straighter.

You are right.. if you have a plane that flies like...
Showing results 1 to 25 of 215
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.