RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 009
Showing results 1 to 13 of 13
Search took 0.61 seconds.
Forum: Marketplace
11-08-2018, 07:52 PM
Replies: 0
Views: 359
Posted By 009

Kingtech k-60

Like new about 4 hours on it since new

Have also available complet fuel system including the bubble trap (CAT)
Forum: RC Warbirds and Warplanes
09-22-2018, 06:23 PM
Replies: 5,152
Views: 1,361,884
Posted By 009

Hi, Problem fix. Air leak thru the gasket...

Hi,

Problem fix. Air leak thru the gasket between the carb and the engine. Thanks everyone for you help and particularly to Bob who light this up.
Forum: RC Warbirds and Warplanes
09-18-2018, 04:17 PM
Replies: 5,152
Views: 1,361,884
Posted By 009

Hi, Yes this engine sit there for more than...

Hi,

Yes this engine sit there for more than 5-6 years. I will retry to enrich the high side and see. It's weird with choke on throttle at idle I get 3000 rpm if a push it to full throttle the rpm...
Forum: RC Warbirds and Warplanes
09-15-2018, 11:15 AM
Replies: 5,152
Views: 1,361,884
Posted By 009

Moki 150 problem

Hi,

I just fire up for the first time my 150. Engine don't start without the choke on it. With the choke even at idle the rpm is high and throttle play don't vary the rpm. The only way to stop it...
Forum: Gas Engines
08-09-2018, 04:26 PM
Replies: 2,806
Views: 708,449
Posted By 009

Battery is a duralite lifepo fully charge ...

Battery is a duralite lifepo fully charge

Plug can't be pull out by hand except if I squeeze the locking wire

If I lean the slow needle to start up the engine I must advance more the throttle...
Forum: Gas Engines
08-09-2018, 03:52 PM
Replies: 2,806
Views: 708,449
Posted By 009

Hi, I just try the 22x10 result 3500 rpm...

Hi,

I just try the 22x10 result 3500 rpm again max.


Any clue what can be wrong?


Thanks
Forum: Gas Engines
08-01-2018, 04:23 PM
Replies: 2,806
Views: 708,449
Posted By 009

You really think is all about the prop? I...

You really think is all about the prop?

I can' tu get access to a prop of this size this week.
Forum: Gas Engines
07-31-2018, 07:04 AM
Replies: 2,806
Views: 708,449
Posted By 009

I saw a video on YouTube with the same and look...

I saw a video on YouTube with the same and look fine
Forum: Gas Engines
07-31-2018, 06:52 AM
Replies: 2,806
Views: 708,449
Posted By 009

Hi, My Saito FG60R3 can't get more than 3300...

Hi,

My Saito FG60R3 can't get more than 3300 rpm (6700 rpm reading out of a two blade digital tach) on my engine.
On full throttle rpm drop sometime to 2700 rpm and go back to 3300 rpm. I did try...
Forum: Gas Engines
06-06-2015, 09:07 AM
Replies: 131
Views: 31,096
Posted By 009

Hi, Can you tell me your cylinder on your...

Hi,

Can you tell me your cylinder on your fg84r3 running at what temp?

What should be the maximum cylinder temp?

Did you perform the air purging procedure as said in the manual?


Thanks...
Forum: Glow Engines
09-09-2008, 07:47 PM
Replies: 5
Views: 863
Posted By 009

RE: FL-70 carb position

Thanks for your advice sir!
Forum: Glow Engines
09-09-2008, 06:11 PM
Replies: 5
Views: 863
Posted By 009

RE: FL-70 carb position

Your right but did you think it will help or I should go with the ram ignition system? Does this carb are really a problem in inverted setup?

Thanks again
Forum: Glow Engines
09-09-2008, 03:56 PM
Replies: 5
Views: 863
Posted By 009

FL-70 carb position

I receive my new FL-70 today, I will mount it inverted, did you think if I rotate the carb the avoid it to be down side up will helb for idle? I will have to built a new fitting to secure it to the...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.