RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Skygopher
Showing results 1 to 20 of 20
Search took 0.76 seconds.
Forum: RC Humor
01-24-2007, 06:53 PM
Replies: 11
Views: 1,305
Posted By Skygopher

RE: Can you read this?

Redfox, thought I'd let you know that the correct spelling of rip is rip not ripe unless your fruit is well done:)
Forum: Gas Engines
07-03-2006, 08:03 AM
Replies: 3
Views: 548
Posted By Skygopher

G-62 jug

I had a small problem with the jug on my G-62 when It hit the ground [:o]. I tried to have it welded but it did not hold. Does anyone have one that they ould like to git rid of? They are on backorder...
Forum: Gas Engines
06-27-2006, 09:20 PM
Replies: 13
Views: 2,315
Posted By Skygopher

Fuel Pump for gas can?

I am looking for a good electric pump to use in fueling my gas engines. Any good ideas? Thanks
Forum: RC Humor
03-26-2006, 12:56 PM
Replies: 19
Views: 2,849
Posted By Skygopher

RE: RC Plane shot down by shotgun!!!???

This guy probably has a loose screw but these news articles are the type of thing that give this hobby a bad name and cause flying sight issues.
Forum: RC Humor
02-16-2006, 07:35 PM
Replies: 29
Views: 4,567
Posted By Skygopher

RE: Funny things when teaching new pilot

This wasn't with a new pilot, but with a rather older pilot. He was on the flight line at the same time as a student and trainer. I was sitting in the shade swapping stories with the other pilots...
Forum: Glow Engines
01-22-2006, 06:13 PM
Replies: 2
Views: 607
Posted By Skygopher

Enya parts

I have been looking all over for a piston ring for an Enya 120 4 stroke. Can anyone help.
Forum: Glow Engines
01-22-2006, 06:09 PM
Replies: 0
Views: 204
Posted By Skygopher

Parts for 120 enya

I am in need of a piston ring for a 4 stroke 120 enya. Have been looking all over and cannot find a source. Can anyone help. Thanks..
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-04-2005, 08:48 PM
Replies: 8
Views: 854
Posted By Skygopher

Engine for 30% Carden Cap 232

I am having a difficult time in deciding what engine to put on a 30% Carden Cap 232. I am looking for one that will give good aeobatic performance and give good reliability. Twins would be Ok. Thanks...
Forum: Gas Engines
03-12-2005, 05:14 PM
Replies: 2
Views: 1,302
Posted By Skygopher

tillotson carb rebuild kit

I have an older Quadra 35 with a tillotson carburetor. Can anyone tell me where to get a rebuild kit for it? Thanks
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-22-2004, 09:07 PM
Replies: 4
Views: 702
Posted By Skygopher

RX crystals.

Can I change a higher channel crystal into a lower channel receiver without causing any frequency problems? Futaba says not to do this. But if I buy a new receiver it is not marked for high or low....
Forum: Giant Scale Aircraft - 3D & Aerobatic
04-22-2004, 12:37 PM
Replies: 4
Views: 1,055
Posted By Skygopher

Balance point on a 1/4 sig cub

Can I get a little help here? I purchased an already built 1/4 Scale SIG Cub and am now ready for it's maiden flight (with me). But I still have to balance her out and am wondering if anyone has the...
Forum: ARF or RTF
01-16-2004, 09:47 PM
Replies: 5
Views: 952
Posted By Skygopher

RE: Extra 300s from world models, any input

Hello, I have one in the purple colors and power it with an O.S. 160. It is a joy to behold... Unlimited vertical once the engine was broken in and it will perform any manuver you want. I am actually...
Forum: Gas Engines
12-29-2003, 08:17 PM
Replies: 7
Views: 923
Posted By Skygopher

RE: Engine Identification Help!

Thanks for the help. I'll get tearing into it soon. Should make my 1/4 scale Sig Cub tear up the skys.Thanks again. This is a great site!!;)
Forum: Gas Engines
12-29-2003, 07:59 PM
Replies: 8
Views: 944
Posted By Skygopher

RE: Engine size

Thanks for all the help. Will start digging into it. I am planning on putting it on a 1/4 scale Sig clipped wing Cub. Should power it like scale.:D:D
Forum: Gas Engines
12-27-2003, 08:57 PM
Replies: 8
Views: 944
Posted By Skygopher

RE: Engine size

Sorry about the screen name but it is one my wife has called me forever and most of my buddies have picked up on it.:eek: I am trying to get my old one back. Anyway, Here are a couple of pics. of the...
Forum: Gas Engines
12-27-2003, 08:50 PM
Replies: 7
Views: 923
Posted By Skygopher

RE: Engine Identification Help!

Here are a couple differant views. Also, How do i get info on how to replace the ignition system?
Thanks, Bob
Forum: The Clubhouse
12-27-2003, 11:46 AM
Replies: 656
Views: 68,241
Posted By Skygopher

RE: What do you do for a living?

Safety Consultant Doing audits, Training, Inspections and stuff.
Forum: Gas Engines
12-26-2003, 02:16 PM
Replies: 8
Views: 944
Posted By Skygopher

Engine size

how did Quadra put the size of their engines on them. I have one and can't see any markings????[:o]
Forum: Questions and Answers
12-26-2003, 02:16 PM
Replies: 0
Views: 315
Posted By Skygopher

MOVED: Engine size

Gas Engines: http://www.rcuniverse.com/forum/fb.asp?m=1378900
Forum: Gas Engines
12-26-2003, 09:51 AM
Replies: 7
Views: 923
Posted By Skygopher

Engine Identification Help!

I recently bought a Quadra engine at the auction of a fellow club member who has passed away. I am not familiar with the Quadras and do not know how to tell what size it is. Any suggestions? Thanks.
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.