RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 4516822
Showing results 1 to 14 of 14
Search took 0.63 seconds.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-25-2004, 05:38 PM
Replies: 21
Views: 1,108
Posted By 4516822

RE: batteries - anyone???

give xs power a try, i have been having great luck with them and so have all the others that have tried them you can email [email protected] or try xspower.org for what they have to offer...
Forum: RC Monster Trucks
02-25-2004, 05:29 PM
Replies: 12
Views: 827
Posted By 4516822

RE: Whats Wrong?

your low end may be lean.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-24-2004, 10:24 PM
Replies: 4
Views: 378
Posted By 4516822

RE: motor wont spin in reverse

The motor probably needs new brushes and a good cleaning, after that it should be fine...
Forum: RC Car General Discussions
02-24-2004, 10:19 PM
Replies: 5
Views: 486
Posted By 4516822

RE: Engine temp???

if you just bash try to keep the engine temp around 210-230 range, and more then that will reduce engine life, but if you race running it at the 250-260 range, NEVER run your engine past 300.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-24-2004, 10:16 PM
Replies: 2
Views: 315
Posted By 4516822

RE: Balance help...

talk to cliff at AE, about mounting more cells and keeping the balance good.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-24-2004, 10:14 PM
Replies: 7
Views: 581
Posted By 4516822

RE: What do I need to upkeep an electric motor

you want to make sure that you use a fiberglass cleaning stick so it wont bend the comm up.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-21-2004, 12:02 PM
Replies: 10
Views: 1,003
Posted By 4516822

RE: Modified motors and high gears..

if you want some really fast motors try out xspower.org they have some ballistic motors, i had one in my etc3 and i beat a gas ntc3 down a 450ft straight away, with gearing you need to be cautious...
Forum: RC 1/8th Scale Buggies
02-21-2004, 11:52 AM
Replies: 9
Views: 1,473
Posted By 4516822

RE: 17t clutch bell or 18t?

I think the manual will have a better recomondation..... usually there is a gearing chart towards the back.
Forum: Traxxas Monster Truck forum
02-21-2004, 11:51 AM
Replies: 69
Views: 3,822
Posted By 4516822

RE: How can I slow the EMAX 25% to 50% ?

Hi, you wont have any problem with the esc, and you dont want to get 1500mah batteries... just get the 3300's if you can afford them, having a lower mah battery wont slow the truck down at all it...
Forum: HPI Monster Truck Forum
02-21-2004, 11:45 AM
Replies: 4
Views: 557
Posted By 4516822

RE: charging a hump pack question

Hi, you want to charge at a maximum of 1.1 amps, but if your not in a hurry just charge at 1amp it will make your pack run longer, and for the mV setting you want 24mV for the whole pack or 4mV...
Forum: RC Nitro Stadium Trucks
02-21-2004, 11:41 AM
Replies: 7
Views: 346
Posted By 4516822

RE: Question about tire foam...........

Hi, you may not want to dremal out your tires.. if you want to make your tires a little softer try putting simple green on them and let them soak and then dry them off and feel how tacky they are.
Forum: RC On Road Nitro Cars
02-19-2004, 09:16 PM
Replies: 15
Views: 877
Posted By 4516822

RE: post your upgrades

Nitro Tc3
Nova Mega .12
motor saver air filter and cover
xs power reciever pack
airtronics m8
94357 servos throttle and steering
foam tires
golden horizon chassis
gh front and rear...
Forum: RC Nitro Stadium Trucks
02-19-2004, 08:58 PM
Replies: 16
Views: 2,190
Posted By 4516822

RE: Proline Blade tire question

No matter what side you put the tire on it will be on the right side, as long as you have glued both tires the same.....
Forum: RC On Road Nitro Cars
02-18-2004, 07:30 PM
Replies: 32
Views: 1,512
Posted By 4516822

RE: I mean...is it the same? It can´t! Check this out people!

I think you all need a little assistance in this area...

Actually, stock plastic versions are more impact-resistant. Plastic parts are more flexible than carbon, allowing more "give" in a...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.