RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dccatl
Showing results 1 to 18 of 18
Search took 0.02 seconds.
Forum: RC Jets
03-07-2018, 08:15 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

I'd be curious to know if it works with a regular...

I'd be curious to know if it works with a regular R7 too. I've just ordered a CB200 for this jet and I'm planning on putting the REX7 in my other jet that I haven't yet converted to Jeti using the...
Forum: RC Jets
03-07-2018, 06:39 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

That's my understanding from speaking to Danny...

That's my understanding from speaking to Danny this morning. Although, I think you might be able to have the REX7 Output PPM to the CB200, just not EX Bus and it would work. I didn't want to go...
Forum: RC Jets
03-07-2018, 06:34 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Not with my current equipment, not enough servo...

Not with my current equipment, not enough servo outputs: REX 7 + R3 = 9 outputs, I need 13.
Forum: RC Jets
03-07-2018, 05:02 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

After a very helpful conversation with Danny this...

After a very helpful conversation with Danny this morning, it turns out that the REX 7 will NOT convert/pass through the PPM signal from the R3 to the EX Bus port. Evidently a REX Assist will do...
Forum: RC Jets
03-06-2018, 04:57 PM
Replies: 3,501
Views: 598,012
Posted By dccatl

That was good advice. I did as you suggested and...

That was good advice. I did as you suggested and disabled the primary RF module, received the loss of signal alarm but I did NOT have control of my primary flight controls from the Cortex Pro via Ex...
Forum: RC Jets
03-06-2018, 11:04 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

OK then, that saves me the trouble of trying the...

OK then, that saves me the trouble of trying the Ex-Bus route. Your rationale for disabling the Morse code alarm makes sense as well, so I will probably end up doing the same.

Thanks again for...
Forum: RC Jets
03-06-2018, 09:16 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Wayne, Yes, I did as you note and disabled the...

Wayne, Yes, I did as you note and disabled the applicable RF unit from the transmitter and verified the alarms and servo control but I'm going to repeat that tonight to make sure. I also did...
Forum: RC Jets
03-06-2018, 05:44 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

I may have spoke too soon. I flew my Joker with...

I may have spoke too soon. I flew my Joker with my new DS-16 for the first time this past weekend with the above receiver settings. First flight was perfect, no trim required in any flight mode....
Forum: RC Jets
02-23-2018, 08:07 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Thanks for following up. I did as you surmised...

Thanks for following up. I did as you surmised and only set the R3 to 30 ms and the R7 is set to Auto. Everything seems to be working perfectly now.
Forum: RC Jets
02-22-2018, 03:39 PM
Replies: 3,501
Views: 598,012
Posted By dccatl

Thank you both. I have set PPM Channels to 13...

Thank you both. I have set PPM Channels to 13 (which I'm using) and output period on the R3 to 30 mSec (2 mSec*13 channels + 4 mSec). No more spurious Loss of PPM (S Alarm).

David
Forum: RC Jets
02-21-2018, 10:31 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Thanks Goose I'll change to 17ms

Thanks Goose I'll change to 17ms
Forum: RC Jets
02-20-2018, 05:33 PM
Replies: 3,501
Views: 598,012
Posted By dccatl

Loss of PPM

I just finished setting up my new DS-16 with my CARF Joker. I’m using a R7 REX and R3/RSW in Dual Path Mode and a Cortex Pro with Ex-Bus. During the course of setting everything up I’ve received a...
Forum: RC Jets
02-15-2018, 06:41 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Perfect! No more trim screen on start up and...

Perfect! No more trim screen on start up and throttle cut works at any throttle level, whereas using the switch with digital trim method would only shutdown the turbine if throttle was < 50 with...
Forum: RC Jets
02-15-2018, 03:54 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

Thanks but I don't think a spring loaded switch...

Thanks but I don't think a spring loaded switch will work for my turbine. I'm already using a 2 position locking switch, using buttons for trimming NWS, all that works perfectly. Just wondering if...
Forum: RC Jets
02-14-2018, 05:40 PM
Replies: 3,501
Views: 598,012
Posted By dccatl

OK I see now, putting my throttle trim on a...

OK I see now, putting my throttle trim on a 2-position switch seems to cause the trim screen to appear on start-up. Is there any way to disable this?
Forum: RC Jets
02-14-2018, 05:33 PM
Replies: 3,501
Views: 598,012
Posted By dccatl

Thanks F1 and Wayne. I've got my flap delay...

Thanks F1 and Wayne. I've got my flap delay working the way I like it now using Butterfly mix. Now I have another question:

At some point during my model set up I changed something that causes...
Forum: RC Jets
02-14-2018, 05:19 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

But won't that delay everything controlled by the...

But won't that delay everything controlled by the flight mode? For example if I have separate gyro settings for flight mode (I don't just using this for an example) I might not want my gyro to...
Forum: RC Jets
02-14-2018, 03:54 AM
Replies: 3,501
Views: 598,012
Posted By dccatl

LA jetguy, I know this is an old post, but just...

LA jetguy, I know this is an old post, but just got my DS-16 and I'm having a heck of time trying to figure out how to get the +/- delay to work in Butterfly. I have 3 flight modes (Normal, Flaps 1...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.