RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: rrengineer
Showing results 1 to 13 of 13
Search took 0.10 seconds.
Forum: Glow Engines
06-23-2012, 04:20 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Well, aren't you the wealth of Fox information! ;^) Mine is the bead blasted crankcase, it's the carb and backplate that is shiny. I went digging through my parts boxes and found a brand new Mac's...
Forum: Glow Engines
06-23-2012, 03:48 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Wow! They just line right up with the holes in the cankcase. I'll have to file down the two little raised bosses above and below the exhaust port for a flush fit. With an exhaust diverter like the...
Forum: Glow Engines
06-23-2012, 02:51 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

I am aware of heat cycling and will break it in this way. I used Dawn Power Dissolver to loosen it up just now. I sprayed some down on the piston and inside on the con rod crank pin. After opening...
Forum: Glow Engines
06-23-2012, 12:58 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

I just got my NIB Fox .29RC for an Ebay auction I won with very little opposition. I am trying to re-create a Little Stick (I have a laser cut short kit) that I had back in 1974. I was stationed in...
Forum: Glow Engines
02-01-2012, 03:31 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Just highlight the link BETWEEN the URL notations in the parentheses, bring it up to your address bar and right click on paste, then hit enter. Easy.
Mike MacLean
Forum: Glow Engines
12-20-2011, 09:28 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Now that I have solved the problem of mounting the Mac's muffler on my .29 I have another problem. Turns out pushing on the throttle lever od the Perry carb resulted in the throttle stop screw...
Forum: Glow Engines
12-09-2011, 09:43 AM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Wow! Nice neat job and reversible too. By the way, I have not run a Fox .29 in many years. What nitromethane percentage is appropriate for this engine?
Mike
Forum: Glow Engines
12-09-2011, 08:40 AM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

The .29 I have has the holes top and bottom of the exhaust port, but no tabs on the side. There is no exhaust baffle. I have bought the Macs muffler you mentioned and will use a strap I have from an...
Forum: Glow Engines
12-09-2011, 06:24 AM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

The .29 I have does not have the exhaust baffle, so I guess it is a later engine. What it does have is a Perry carb. I have not run it yet, but from what you say the Perry carb is an improvement. ...
Forum: Glow Engines
12-08-2011, 07:23 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

What's the difference between two Fox .29 RC engines where one has a rotating flap in the exhaust and the other does not. I'm guessing the one with the flap is an older version. When did they...
Forum: Glow Engines
11-30-2011, 07:24 AM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

I just acquired an old Fox .29 RC like I had on my Little Stik back in 1974. I plan to build another Little Stik from a short kit that Eddie at Lazer Works cut for me. The engine has a nice little...
Forum: Glow Engines
10-17-2011, 11:11 AM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Thanks erlwb, I was worried about my memory. Apparently I'm not that old yet. Yes, that looks like the one I had. I wasn't using an APC prop back then though. Just for a kick, I would love use a...
Forum: Glow Engines
10-16-2011, 06:53 PM
Replies: 5,192
Views: 566,948
Posted By rrengineer

RE: Club FOX!

Back in 1972 I was stationed at Korat AB in Thailand. They had a hobby shop on base with a limited selection of kits and engines. I picked up a Little Stick and I am sure I used a Fox .29 R/C. I...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.