RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: why-me
Showing results 1 to 10 of 10
Search took 0.01 seconds.
Forum: RC Jets
04-26-2019, 03:32 PM
Replies: 1,631
Views: 334,160
Posted By why-me

​​​it's just the way the pic looks. It is a...

​​​it's just the way the pic looks. It is a antenna holder kit from hobby king. The straws that hold the antennas are at 45°so they hold them at 90°.
Forum: RC Jets
04-26-2019, 11:35 AM
Replies: 1,631
Views: 334,160
Posted By why-me

They should be 90° to each other. I used this...

They should be 90° to each other. I used this setup in my T1https://cimg2.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1500x2000/20181108_155349_701b0dddfe5f8f06e13457bcea8377c7a0f6c6cd.jpg
Forum: RC Jets
05-21-2018, 04:04 AM
Replies: 1,631
Views: 334,160
Posted By why-me

Flap trim

I agree with starting at zero and adjust in flight in all flap settings
Forum: RC Jets
05-20-2018, 06:26 PM
Replies: 1,631
Views: 334,160
Posted By why-me

Down elevator

Your best bet is to set your elevator trim in your flap function in your radio to be able to adjust trin in each flap setting. Takes the guess work out of setting a percentage. Take off and set trim...
Forum: RC Jets
01-25-2018, 07:38 PM
Replies: 1,631
Views: 334,160
Posted By why-me

CG and placement of equipment

20180111_204243.jpgMy brother and I are just completing 2 mini T- ones. I know there had been a lot of discussion on here about CG. We built both the same and put all equipment in the same locations...
Forum: RC Jets
01-24-2018, 06:55 AM
Replies: 1,631
Views: 334,160
Posted By why-me

measure in from the rear to the front of the...

measure in from the rear to the front of the tube, made sure it's the front of tube not the bell housing disagree that is inserted front of tube. Than set your turbine in place and measure from the...
Forum: RC Jets
01-24-2018, 01:21 AM
Replies: 1,631
Views: 334,160
Posted By why-me

Should be flush with the rear of fuselage

Should be flush with the rear of fuselage
Forum: RC Jets
01-04-2018, 10:47 PM
Replies: 1,631
Views: 334,160
Posted By why-me

tailpipe should be even with rear of fuselage. ...

tailpipe should be even with rear of fuselage. It should not protrude at all
Forum: RC Jets
01-04-2018, 10:43 PM
Replies: 1,631
Views: 334,160
Posted By why-me

Balance

Gear down and uat full
Forum: RC Jets
11-29-2017, 02:30 PM
Replies: 1,631
Views: 334,160
Posted By why-me

Wing servos

Yes you have to hard mount your servos
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.