RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: JustPlaneCrazy3D
Showing results 1 to 17 of 17
Search took 0.10 seconds.
Forum: 3D Flying!
04-03-2006, 11:14 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

LOL !!

Good Luck !
Forum: 3D Flying!
04-03-2006, 10:16 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

maxun -

The CRRC PRO sounds great, I've been curious about them, let us know how it flies.
Forum: 3D Flying!
04-03-2006, 08:23 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

I finally maidened mine yesterday.


WOW, what a great flying plane.

Gear I am using,

ZDZ50
Hitec HS645MG's on everything.
Made it into a Pull-Pull rudder using a Hitec HSC-5955TGS
Forum: 3D Flying!
03-23-2006, 09:31 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

That sounds real nice, how far is Chillicothe from Cleveland ?

What's the name of the club you fly at ?
Forum: 3D Flying!
03-22-2006, 04:37 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Yes, going South sounds real NICE about now.

I'm just waiting for a small crack in the door and I'm outta Ohio.
Forum: 3D Flying!
03-22-2006, 03:31 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Thanks !!!

Well the way the weather here in the Cleveland area is I may not maiden it for another month @##@@%!@@@

Anyone out in there in a warm state that needs a controls technician ?? LOL
Forum: 3D Flying!
03-22-2006, 03:08 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Thanks, bubbagates !


I can't wait to maiden it.
Forum: 3D Flying!
03-22-2006, 02:05 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

I haven't got an accurate weight yet but I'm thinking it will be around 15 to 16 lbs.

I will weigh it when I can though.
Forum: 3D Flying!
03-22-2006, 01:25 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

I've got a ZDZ 50 in it, I have not yet maidened it though, waiting for the weather.
Forum: 3D Flying!
03-22-2006, 12:02 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

I used all CA hinges, I used the 1 inch wide and the 3/4 inch wide next to one another, this should be more than adequate.
Forum: 3D Flying!
03-03-2006, 11:20 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Thanks jeyre!

Good Luck on the new Ultimate.
Forum: 3D Flying!
02-17-2006, 04:52 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Man that's a very nice setup !

Where did you get the clips that the wires are connected too ?

They look a little like battery bars.

Thanks !
Forum: 3D Flying!
02-02-2006, 01:01 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Thanks guys !

I can't wait to get the engine next week and finish her up.
Forum: 3D Flying!
02-02-2006, 10:04 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Well I made my rudder setup into a Pull-Pull configuration, it turned out absolutely perfect.

Here are some pics of it.
Forum: 3D Flying!
01-31-2006, 09:25 AM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Has any one set up there ultimate with a Pull-Pull setup.

I was looking at mine last night and noticed some pull-pull exit holes already cut in the fuse sides below the elev. servos.

I am...
Forum: 3D Flying!
01-26-2006, 02:16 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

Well glow is really not my goal, but I do have a Moki 2.10 laying around gathering dust.
I know the biggest drawback to glow would be fuel cost.

Sounds like the Moki 2.10 would have enough...
Forum: 3D Flying!
01-26-2006, 12:36 PM
Replies: 7,031
Views: 764,309
Posted By JustPlaneCrazy3D

RE: Great planes ultimate 160

I've looked through this entire post and did not see too much mentioned about using a Moki 2.10 for the engine and what kind of performance the plane would have using it.

I am thinking about...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.