RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Auburn02
Showing results 1 to 17 of 17
Search took 0.01 seconds.
Forum: RC Jets
02-02-2021, 07:59 PM
Replies: 978
Views: 200,049
Posted By Auburn02

If you pinch off the green line to the right...

If you pinch off the green line to the right cylinder, will the left one unlock the gear by itself or does it bind just the opposite of how it’s doing now?
Forum: RC Jets
02-01-2021, 07:42 AM
Replies: 978
Views: 200,049
Posted By Auburn02

Gary, I assume there is no lock of any sort, is...

Gary, I assume there is no lock of any sort, is the friction fit alone sufficient that it will stay extended in flight?
Forum: RC Jets
01-05-2021, 07:57 PM
Replies: 978
Views: 200,049
Posted By Auburn02

It's nothing more than a hunch, but I think this...

It's nothing more than a hunch, but I think this airplane is going to be much more of a pig (I don't mean that in a bad way!) than a Havoc or F-16, so you may find yourself using a much higher...
Forum: RC Jets
09-14-2020, 08:47 PM
Replies: 978
Views: 200,049
Posted By Auburn02

Yep Tom beat me to it, on the ground when people...

Yep Tom beat me to it, on the ground when people look at it the gear will be down and doors open, thus hinge not visible in the inlet.
Forum: RC Jets
09-09-2020, 05:14 PM
Replies: 978
Views: 200,049
Posted By Auburn02

How much smaller? That Y reduces from a single...

How much smaller? That Y reduces from a single 4mm inlet line to twin 3mm outlet lines which would allow you to feed a 4mm line from the valve to the Y, then 2x 3mm lines (i.e. the red lines in your...
Forum: RC Jets
09-08-2020, 07:56 PM
Replies: 978
Views: 200,049
Posted By Auburn02

How about these? ...

How about these?

https://www.aeropanda.com/collections/festo-3mm-fittings/products/festo-push-in-y-connector-4mm-3mm
Forum: RC Jets
06-04-2020, 05:58 AM
Replies: 978
Views: 200,049
Posted By Auburn02

Man I'm even getting great ideas from this thread...

Man I'm even getting great ideas from this thread that aren't part of this thread! You the man, Gary!
Forum: RC Jets
02-07-2020, 06:04 AM
Replies: 978
Views: 200,049
Posted By Auburn02

I love threads like this. Come for the progress,...

I love threads like this. Come for the progress, stay for the tips I would have never thought of but will remember forever.
Forum: RC Jets
01-27-2020, 01:01 PM
Replies: 978
Views: 200,049
Posted By Auburn02

Sure does, good call Bob. I've got a couple that...

Sure does, good call Bob. I've got a couple that are just the opposite so that was the first thing I thought of.

Carry on with the good work Gary!
Forum: RC Jets
01-26-2020, 08:20 PM
Replies: 978
Views: 200,049
Posted By Auburn02

This may have been what Matt was already alluding...

This may have been what Matt was already alluding to, but keep in mind the compression of your struts on touchdown. The way you’ve cut out relief for the tires is great but only works in the extended...
Forum: RC Jets
09-18-2019, 08:47 PM
Replies: 978
Views: 200,049
Posted By Auburn02

Also, what about using a full servo arm and a...

Also, what about using a full servo arm and a pull pull rod/ball link setup to let the servo have a little more control in keeping the spindle centered and sturdy?
Forum: RC Jets
09-17-2019, 11:00 AM
Replies: 978
Views: 200,049
Posted By Auburn02

The measurements are different. Is that...

The measurements are different. Is that intentional?

Side note: still love every update in this thread, nothing but fantastic idea after fantastic idea.
Forum: RC Jets
02-25-2019, 07:43 AM
Replies: 978
Views: 200,049
Posted By Auburn02

Wait, is there a current build ongoing? I thought...

Wait, is there a current build ongoing? I thought he was pretty much gone from the boards, if not the hobby altogether.
Forum: RC Jets
02-01-2019, 07:01 AM
Replies: 978
Views: 200,049
Posted By Auburn02

He mentioned it in his post, it was most likely...

He mentioned it in his post, it was most likely placed there to aid in feeding a wire for the installation of a light system. If you think about it, it's pretty funny/sad how someone would have the...
Forum: RC Jets
12-13-2018, 07:47 AM
Replies: 978
Views: 200,049
Posted By Auburn02

I had a thought along the same lines as maury,...

I had a thought along the same lines as maury, but I was thinking more of a hand tightened knurled head nut rather than something requiring a ratchet.

Seems like your current approach will work...
Forum: RC Jets
09-12-2018, 06:03 AM
Replies: 978
Views: 200,049
Posted By Auburn02

I only came across his YouTube channel while...

I only came across his YouTube channel while watching random videos about glass (crash) repairs, once I discovered it I think I lost a solid 2 days of productivity to his videos. :eek:
Forum: RC Jets
09-05-2018, 06:00 AM
Replies: 978
Views: 200,049
Posted By Auburn02

Love seeing a real build thread like this, keep...

Love seeing a real build thread like this, keep it up!
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.