RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Simou
Showing results 1 to 12 of 12
Search took 0.12 seconds.
Forum: Gas Engines
02-16-2007, 09:02 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

I hope this helps.

http://tinyurl.com/22xjyg

I wrote it in italian, the translation by google is terrible, please be patient....
:eek:

Simone
Forum: Gas Engines
12-05-2006, 03:45 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

also mine it is only the logical part, I kept the original CDI. With the second pickup I fire up the engine by hand, without any kickback. Soon I will share my code on my homepage.

Simone
Forum: Gas Engines
12-04-2006, 10:51 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

i've already done it ;) but I don't plan to sell anything.
I improved the logic part of the project you can see at http://www.modelbouw.gompy.net/newcdi/newcdi.htm, using a second pickup unit for...
Forum: Gas Engines
09-21-2006, 08:56 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

1/2 turn on these needles is an enormity... low needle affects full throttle too much. I didn't asked about RPM for adjusting purpose: gf45 is on a tug and I want to know the overall performance of...
Forum: Gas Engines
09-21-2006, 03:14 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

RichAur,
I agree... this engine is very difficult to properly tune.
What rpm should it turn an APC 20x8W?
tnx

Simone
Forum: Gas Engines
09-20-2006, 03:08 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

I bought a MVVS 45 IRS MG w/canister, instead..... ;)

....but for my tug plane CRRC would be better.

Simone
Forum: Gas Engines
09-20-2006, 02:21 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

Yesterday I tried a CDI from a new in box GF45i, same version of mine. Same kind of problems: the engine runs rich, even with the needle closed. I also tried another carb and even a new needle on my...
Forum: Gas Engines
09-15-2006, 03:28 PM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

I've found the best is with this mark opposite from the engine shaft... Is my magnetic pin mounted reversed??? Briefly, my engine runs rich, at a unstable rpm. Adjusting needles does not take any...
Forum: Gas Engines
09-15-2006, 02:25 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

After several trials, my motor still starts surging above half throttle. Idle is good. I have no cowl, tried 95 and 98 octane fuel, tried both synthetic and mineral oil, tried some works on the...
Forum: Gas Engines
04-16-2006, 04:24 PM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

I experience some trouble starting it inverted. It require many flip to prime, then it get immediately flooded and kick back hard. Holding the plane with vertical wings (the engine lays on his side)...
Forum: Gas Engines
03-27-2006, 07:09 AM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

mine has the metal carbi support and the rounded muffler, the ignition is similar to the black one but it is GRAY.

SMU
Forum: Gas Engines
03-22-2006, 04:31 PM
Replies: 1,644
Views: 281,104
Posted By Simou

RE: CRRC GF45i

... Someone has a video of this engine running well!?

tnx in advance

SMU
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.