RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ochsnm00
Showing results 1 to 11 of 11
Search took 0.10 seconds.
Forum: Glow Engines
05-31-2018, 03:55 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

I have a pulse type mounted on an OS 160. It...

I have a pulse type mounted on an OS 160. It works fine. It's on a 2 meter plane with a center tank. The pump is mounted on the engine. I was afraid to drill a hole in my new OS. Since then I've had...
Forum: Glow Engines
12-24-2017, 08:32 AM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

Value

The best way to find anything's value is to go to ebay and click on "advanced" in the upper right hand corner. Check the "sold" box. Fill in your info and search. From what I can tell; NIB $60, used...
Forum: Glow Engines
10-11-2017, 06:22 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

Wow, I didn't think you knew what you were...

Wow, I didn't think you knew what you were talking about so I went over to MECOA and there they are, beautiful Fox parts, with more to come. They also acquired Webra recently.
Forum: Glow Engines
01-06-2017, 08:17 AM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

[QUOTE=MattMathison;12293199]Need help! Got an...

[QUOTE=MattMathison;12293199]Need help! Got an older Fox .40 dbb and baffled but came used w/o piston ring. Otherwise engine looks immaculate. It's older than my .40 Deluxe but is scant of...
Forum: Glow Engines
01-06-2017, 08:07 AM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

http://aeroscott.com/ Try this business to see...

http://aeroscott.com/ Try this business to see if they can fabricate a ring.
Forum: Glow Engines
06-26-2016, 03:32 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

The prop driver is on a tapered shaft, you may...

The prop driver is on a tapered shaft, you may think it is really stuck until it pops right off. Put the engine in the freezer, after it's cold quickly heat the driver with a propane torch until spit...
Forum: Glow Engines
04-27-2016, 01:13 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

This article should help. ...

This article should help. http://www.fayettevillercclub.com/id68.html
Forum: Glow Engines
04-27-2016, 12:40 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

If there is too much blow by the crankcase...

If there is too much blow by the crankcase pressure will be too low to force the fuel mix into the combustion chamber. To test remove the glow plug and turn the engine over smartly. You should hear a...
Forum: Glow Engines
03-31-2016, 08:19 AM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

[QUOTE=carlgrover;12194948]High speed needle is...

[QUOTE=carlgrover;12194948]High speed needle is not too lean. I always have a smoke trail. No amount of tuning has fixed this problem. Needles aren't dirty. I recently cleaned the entire carb. I've...
Forum: Glow Engines
01-07-2016, 06:10 AM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

Both Eagle III 60 needle valves

Both Eagle III 60 needle valves
Forum: Glow Engines
01-06-2016, 07:56 PM
Replies: 5,192
Views: 565,126
Posted By ochsnm00

Does anyone know what has happened to Fox engine...

Does anyone know what has happened to Fox engine parts since they stopped building engines. I've been on the Fox machine site and there is no mention of parts. Is anyone selling parts?
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.