RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: w8ye
Showing results 1 to 12 of 12
Search took 0.01 seconds.
08-18-2016, 03:59 AM
Replies: 246
Views: 51,352
Posted By w8ye

There was a problem with some of the big bore...

There was a problem with some of the big bore piston and cylinder kits for the 660 having the piston skirt touch the counter weight and also some kits the cylinder flange extension would touch bottom...
11-24-2015, 05:16 AM
Replies: 246
Views: 51,352
Posted By w8ye

Don't forget to have a radius to the inside...

Don't forget to have a radius to the inside corners or you will create stress points
11-08-2015, 02:57 PM
Replies: 246
Views: 51,352
Posted By w8ye

Looks like an old prewar South Bend lathe common...

Looks like an old prewar South Bend lathe common instuitional lathe of the era in the USA
10-20-2015, 01:08 PM
Replies: 246
Views: 51,352
Posted By w8ye

If using a aftermarket cylinder and piston, do...

If using a aftermarket cylinder and piston, do not just assume everything fits perfect as you might with genuine Stihl parts.

Observe the piston skirt to crank counter weight clearance as well as...
10-17-2015, 09:02 AM
Replies: 246
Views: 51,352
Posted By w8ye

This is the key element in Zagnut's discussion ....

This is the key element in Zagnut's discussion . . .

"the whole idea behind this method is that it guarantees perfect concentricity without the need for any indicating or aligning. swapping a part...
10-16-2015, 04:22 AM
Replies: 246
Views: 51,352
Posted By w8ye

+1 on what Zagnut said

+1 on what Zagnut said
10-14-2015, 05:46 AM
Replies: 246
Views: 51,352
Posted By w8ye

The clutch side bearing is 17 X 40 X 14 and is a...

The clutch side bearing is 17 X 40 X 14 and is a Stihl bearing Notice that it is wider than standard?

The flywheel side is a 6203 which is 17 X 40 X 12

It might not make any difference on the...
10-12-2015, 05:09 PM
Replies: 246
Views: 51,352
Posted By w8ye

There's a special tool for getting the case...

There's a special tool for getting the case halves apart. The tool looks like a big C-clamp. The "C" part reaches inside the case and pushes (It pulls?) on the case towards the outside and the screw...
10-12-2015, 04:01 PM
Replies: 246
Views: 51,352
Posted By w8ye

You best measure the rear bearing too? Stihl is...

You best measure the rear bearing too? Stihl is notorious using a odd ball proprietary bearing on the clutch side. And the MS 660 was no exception.
10-11-2015, 06:50 PM
Replies: 246
Views: 51,352
Posted By w8ye

to post pictures, you are given the opportunity...

to post pictures, you are given the opportunity by using the "Go Advanced" option in the lower right corner.

You can also use the insert image picture icon in the quick reply editor.

In both...
10-11-2015, 05:01 AM
Replies: 246
Views: 51,352
Posted By w8ye

The clutch is left handed

The clutch is left handed
10-09-2015, 04:12 AM
Replies: 246
Views: 51,352
Posted By w8ye

A Stihl MS660 is 92cc from the factory and the...

A Stihl MS660 is 92cc from the factory and the big bore cylinder & piston makes it 99cc
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.