RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: lxfly
Showing results 1 to 17 of 17
Search took 0.02 seconds.
Forum: RC Jets
05-17-2017, 02:31 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

Seems to be the best and simplest solution for...

Seems to be the best and simplest solution for the flaps and I should go this way. Just missed the specific butterfly setting for different phases 5 years ago when I programmed my first jet and then...
Forum: RC Jets
05-15-2017, 10:45 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

I just do it like Arjan described except that I...

I just do it like Arjan described except that I use the butterfly facility for all my jets in the landing phase.

Use the phase switch to activate the butterfly and then I set fix positions for...
Forum: RC Jets
03-11-2017, 12:26 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

RTFM: the red plugfrom MSPEED can optionally be...

RTFM: the red plugfrom MSPEED can optionally be connected to a spare channel, in order to control the alarmsignals
I use it with a phase switch to have the low speed alarm announced only on the...
Forum: RC Jets
12-21-2016, 01:50 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

This problem is also reported in the german...

This problem is also reported in the german jetiforum, so seems to be confirmed!
Forum: RC Jets
12-09-2016, 11:31 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

1) I see there are some labeled "REX", and in the...

1) I see there are some labeled "REX", and in the description they seem to be the newer Rx's. I also see they have a 32 bit microcontroller. None of my jets are overly complex... so should I just get...
Forum: RC Jets
04-21-2016, 11:53 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

In addition to the suggested answers: I'm using...

In addition to the suggested answers:
I'm using 3 flight phases for flying, starting and landing so I'm free to manipulate all throws, dual rates, expo etc. for all separate phase. I use and...
Forum: RC Jets
10-14-2015, 05:08 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

As stated, just fly it with CB200 and satellite...

As stated, just fly it with CB200 and satellite receivers. I use always Life batteries, just regulate down to 6V for normal servos; CB200 specifications are from 4..14V.
Forum: RC Jets
10-13-2015, 10:51 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

Why using a PDS with the CB200? Do you need 6V...

Why using a PDS with the CB200?
Do you need 6V for servos or HV? On HV, just connect your batteries to the CB200, for low voltage just use a BEC system from Jeti or a Powerbox Gemini 2, there may...
Forum: RC Jets
03-07-2015, 02:00 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

Hi Dave, Did you copy the model ot di you make...

Hi Dave,
Did you copy the model ot di you make a new model from scratch? If you copied, dual path should be configured, otherwise you have to reconfigure dual path for the F16.

For the the rudder...
Forum: RC Jets
08-26-2014, 10:21 PM
Replies: 3,501
Views: 598,380
Posted By lxfly

How to combine this 2 tries as you also may use...

How to combine this 2 tries as you also may use function curves for the mixer ie set the 3 point curve in the mixer and enable the mixer when gear is out.
If you have a problem with dual rate,...
Forum: RC Jets
08-26-2014, 04:23 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

Hi Pete, You just have to get the logic once....

Hi Pete,
You just have to get the logic once. For every programming function you have a global or a separate setting mode.

As long as you have no extra flight mode programmed , every functions...
Forum: RC Jets
08-26-2014, 03:53 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

As you get the 4 antenna signals, both receivers...

As you get the 4 antenna signals, both receivers seem to work fine. Or you have a bad connection between R9 and satellite or you just got a timing problem when switching on.

Try following: Switch...
Forum: RC Jets
06-05-2014, 06:53 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

Yes, agree! Use the Jeti TX modules since the...

Yes, agree! Use the Jeti TX modules since the beginning in my 20 year old transmitters and have a DC-16 of the first serie, all working without any problem.
Forum: RC Jets
05-29-2014, 05:27 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

Found this in the german...

Found this in the german Jetiforum:http://www.newark.com/te-connectivity-raychem/m...ptc-reset/dp/42M2350
It's some kind of this PTC fuse type that is used.
you may find some details here:...
Forum: RC Jets
05-29-2014, 02:53 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

From Jeti Manual: 3.2 Overload protection of...

From Jeti Manual:
3.2 Overload protection of servos
The Central Box has an overload protection circuit on every servo
output. In case of an overload, the affected servo output is
disconnected...
Forum: RC Jets
05-27-2014, 04:11 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

Hi Mort, tuned a CB200 with 2 Sat2 last week...

Hi Mort,
tuned a CB200 with 2 Sat2 last week but still deedn't fly with it.
But with version 1.11 CB200 is working normally, except that you have the warning on TX 3.0 software. V1.2 should be out...
Forum: RC Jets
05-16-2014, 01:38 AM
Replies: 3,501
Views: 598,380
Posted By lxfly

@treesnake Sent you a pm

@treesnake
Sent you a pm
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.