RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Dansy
Showing results 1 to 22 of 22
Search took 0.01 seconds.
Forum: RC Jets
01-08-2023, 11:29 AM
Replies: 87
Views: 21,793
Posted By Dansy

‘I build 2 of them and on both of them I made...

‘I build 2 of them and on both of them I made the stabs removable…..but I hysol the fin in….

I used a flat carbon Fiber plate to fasten the stab…..
Forum: RC Jets
04-19-2022, 11:39 AM
Replies: 87
Views: 21,793
Posted By Dansy

I used the Pro-link in mine, that was from...

I used the Pro-link in mine, that was from Dreamworks…..if all fail I’m Electron (USA) can square you….under JAG RC
Forum: RC Jets
07-05-2021, 06:15 AM
Replies: 87
Views: 21,793
Posted By Dansy

CM Jets are good.....I have/had many of them :)

CM Jets are good.....I have/had many of them :)
Forum: RC Jets
07-05-2021, 04:23 AM
Replies: 87
Views: 21,793
Posted By Dansy

First you should ditch that tank and get...

First you should ditch that tank and get something with vent and feed on different fitting….I think Dreamworks sell one for this jet.

Using carpet cleaner K2R should lift the fuel from the wood, I...
Forum: RC Jets
06-29-2021, 11:44 AM
Replies: 87
Views: 21,793
Posted By Dansy

I don’t believe it’s still produced, it was a...

I don’t believe it’s still produced, it was a cooperation between a few vendors..and I know of one other vendor that hasn’t had any for a while now…that’s probably just inventory left……
Forum: RC Jets
03-02-2021, 06:23 PM
Replies: 87
Views: 21,793
Posted By Dansy

The 2 I had didn’t need any weight...one with...

The 2 I had didn’t need any weight...one with K100 one with a K120....
Forum: RC Jets
03-02-2021, 12:47 PM
Replies: 87
Views: 21,793
Posted By Dansy

Ouch, not sure the airframe can take that ;)

Ouch, not sure the airframe can take that ;)
Forum: RC Jets
02-28-2021, 01:04 PM
Replies: 87
Views: 21,793
Posted By Dansy

‘Not sure what covering is used on the...

‘Not sure what covering is used on the ventrix.....but it will loosen again and again....
Forum: RC Jets
02-27-2021, 02:39 PM
Replies: 87
Views: 21,793
Posted By Dansy

I had a 120 G2 in mine...

I had a 120 G2 in mine...
Forum: RC Jets
02-27-2021, 03:53 AM
Replies: 87
Views: 21,793
Posted By Dansy

Just batteries on the 2 I flew...with the uat...

Just batteries on the 2 I flew...with the uat further forward....
Forum: RC Jets
01-21-2021, 02:57 PM
Replies: 87
Views: 21,793
Posted By Dansy

Mine's was the same......

Mine's was the same......
Forum: RC Jets
11-20-2020, 02:44 PM
Replies: 87
Views: 21,793
Posted By Dansy

And I taught a 120 was a little much for mine ;) ...

And I taught a 120 was a little much for mine ;)

don’t have many photo’s of the interior....I no longer have that plane...anyway here what I have...
...
Forum: RC Jets
11-20-2020, 05:21 AM
Replies: 87
Views: 21,793
Posted By Dansy

Will do later today on my tablet it's easier....

Will do later today on my tablet it's easier....
Forum: RC Jets
11-20-2020, 04:55 AM
Replies: 87
Views: 21,793
Posted By Dansy

I didn't used the aluminium pieces.....I cut the...

I didn't used the aluminium pieces.....I cut the fiberglass that was in the kit and hysol them.....for the stabs I used a 2mm Carbon Fiber piece that I made...the fin & rudder were hysol in place....
Forum: RC Jets
05-23-2018, 02:20 PM
Replies: 87
Views: 21,793
Posted By Dansy

I'm using the Bundle one and it works fine....

I'm using the Bundle one and it works fine....
Forum: RC Jets
09-19-2017, 01:42 PM
Replies: 87
Views: 21,793
Posted By Dansy

I got a couple flights on mine still adjusting...

I got a couple flights on mine still adjusting the c&g I stated at 180mm back, but I slowly removed the dead weight...had 169g but removed 40g so far, I have 4 batteries in the nose ;)

I was at...
Forum: RC Jets
08-14-2017, 09:31 AM
Replies: 87
Views: 21,793
Posted By Dansy

I always replace Chinese ball link with Korean...

I always replace Chinese ball link with Korean one LOL (secraft).....
Forum: RC Jets
08-14-2017, 08:07 AM
Replies: 87
Views: 21,793
Posted By Dansy

'I'm just finishing one myself......ya there's a...

'I'm just finishing one myself......ya there's a bunch of issues not a quick ARF for sure. I'm waiting for my fuel tank...
Forum: RC Jets
08-10-2017, 08:57 AM
Replies: 87
Views: 21,793
Posted By Dansy

I called and they told me they don't, which is...

I called and they told me they don't, which is fine not a deal breaker for me since I make my own decals....
Forum: RC Jets
07-20-2017, 05:55 AM
Replies: 87
Views: 21,793
Posted By Dansy

Well not really because I have one of the said...

Well not really because I have one of the said kit.....and there's no Audi, Shell, or Michelin decals....which leave the world ventrix.....and number 1, and 4 flags that I won't use ;)
Forum: RC Jets
07-19-2017, 02:09 PM
Replies: 87
Views: 21,793
Posted By Dansy

On the other hand letting those little decals on...

On the other hand letting those little decals on toy planes would just be free publicity LOL �� ya I know doesn't work that way....
Forum: RC Jets
07-19-2017, 11:41 AM
Replies: 87
Views: 21,793
Posted By Dansy

I guess they also took the shell.....Audi....and...

I guess they also took the shell.....Audi....and bosh....because those are not on the decal sheet I got?

i just finish unpacking the plane, pretty nicely done for a wood plane, I looking forward...
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.