RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: stall_warning
Showing results 1 to 14 of 14
Search took 0.04 seconds.
Forum: Extreme Speed Prop Planes
06-09-2011, 05:46 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

I did fairing removed. It was a little nose heavy, added 1/2 oz in the tail later.
Forum: Extreme Speed Prop Planes
06-09-2011, 03:10 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

I put mine in the tail. At first, was going to run #16 wire to the front. Instead I used servo wire. Ran 2 from the battery,
2 switches for redundancy and low loss, feeds 2 separate ports on the...
Forum: Extreme Speed Prop Planes
01-23-2011, 07:13 AM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

I've yet to see a post confirming that they measured as shown in the manual.

If using a 4 cell pack, try a 5 cell pack of your electronics can run on 6 volts.

I'm not using the stock...
Forum: Extreme Speed Prop Planes
01-16-2011, 03:40 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

That was my first option. I Ran down the connectors further.
I didn't use the stock setup. The "Y" pushrod had undersized threads on one side and was able to pull
off the clevis.

Be sure...
Forum: Extreme Speed Prop Planes
01-16-2011, 03:27 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

Had the same problem with the elevator torque rods so I don't think you did anything wrong.
Forum: Extreme Speed Prop Planes
01-13-2011, 05:17 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

For battery selection, I usually wait to see what was needed to balance.
I'll use a 2 cell LIFE battery with dual switches, no regulator. The downside to this is that the balancing leads
need to...
Forum: Extreme Speed Prop Planes
01-13-2011, 05:03 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

Another option would be the
HYPERION ATLAS DS 16 FCD PROGRAMMABLE DIGITAL SERVO

More expensive tho.
Forum: Extreme Speed Prop Planes
01-04-2011, 06:09 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

To measure for the balance point, do as the picture in the manual? The wing is mounted, the fake intake installed and then
measure back from the exposed point on the leading edge?

In other...
Forum: Extreme Speed Prop Planes
01-01-2011, 06:31 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

I removed the Red from the cowl. Use isopropyl alcohol. Don't use CaDebond - fingernail polish remover as it will attack the White.
Once removed, got a surprise. They sanded the White under the Red...
Forum: Extreme Speed Prop Planes
12-29-2010, 06:20 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

[/quote]

should I spray a coat of fuel proof clear coat on the cowling?


[/quote]

Test it first. In an earlier message, someone tried it and it curled.
Forum: Extreme Speed Prop Planes
12-27-2010, 06:00 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

If you use a marker to outline the cowl cutout, and you use isopropyl alcohol to remove the marker, you will also remove
the red paint. No big deal. I'm going to repaint mine with Red Lipstick....
Forum: Extreme Speed Prop Planes
11-15-2010, 08:33 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

Hopefully Horizon can come up with a solution.

Otherwise, I'm looking at stripping the paint, repainting with two colors while trying to match
the Fuse. It will irritate me.
Forum: Extreme Speed Prop Planes
11-14-2010, 11:16 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

Sorry I wasn't clear,

Put the calipers on the threads. One side measures 1.94mm the other 2.05mm
Forum: Extreme Speed Prop Planes
11-14-2010, 10:44 PM
Replies: 1,621
Views: 237,657
Posted By stall_warning

RE: H9 Jackal 50 Prop Jet

Check the Clevis on the elevator split push rod. I can pull one of them off.
One side measures 1.94, the other 2.05. I'll have to fabricate something different.

Any ideas about the Cowl paint...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.