RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: hics3968
Showing results 1 to 15 of 15
Search took 0.08 seconds.
Forum: Gas Engines
11-06-2007, 10:51 AM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

I had same issue with my Thor 45. Changed to DL50 Available from DLUSA.Net for $390.00 comes all accessories.
Installed on 25% Patty and run's awesome.
Forum: Gas Engines
06-12-2007, 11:02 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

This engine does run. I think the problem I had with it is that elavation is too high 4200-4500 feet.
It ran great in Las Vegas Nv. and in Salina Ks. while visiting parents. I think we called...
Forum: Gas Engines
06-11-2007, 09:10 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Your luck must be better than mine.
Wanna buy a second one?????
Forum: Gas Engines
06-11-2007, 09:17 AM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

It's a GREAT engine!!!:D
Very little tuning out of box. Broke in with 20-8 prop.
Now swinging 22-8 on 25% Patty Wagstaff with ease.
Forum: Gas Engines
06-11-2007, 12:05 AM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Yes you can get advanced ignition and plug from western hobbies. But by that time your over $400.
DL-50 is less money with all goodies.
Forum: Gas Engines
06-08-2007, 10:28 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Had same problem on My Patty before switching to DL-50.
I used the measurements instead of the pattern.
Also beefed up inside of firewall with 1/8in plywood after drilling wrong holes from...
Forum: Gas Engines
06-03-2007, 08:06 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Tried advised plug on post 260 and new advanced ignition and changed timing, still no help.
First flight on 25% Patty took half of the runway to take off and when airborne had to fly at full...
Forum: Gas Engines
06-03-2007, 07:32 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Scrap it!!! I had same issue at 4000 feet .
Switched to DL50 on a 25% Patty and what a change.
Forum: Gas Engines
05-08-2007, 11:08 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

The sensor on module went bad.
Switced to advanced module and changed to NGK plug with help from RCIGN1 in Williams Az. and problem solved in less than an hour.
Forum: Gas Engines
05-06-2007, 11:01 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

If anyone has problems with this 45cc engine or any other gas engine for that matter contact Ralph in Williams Az.
His comment to skreamer and myself was to take a drive up the hill and (that it...
Forum: Gas Engines
05-04-2007, 02:35 AM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Thanks for your reply from Okla. and otrhers.
For Okla. my ?? is what gap are you using on spark plug, whether it be Torgue that it came with or did you change???
Thanks
Kevin
Forum: Gas Engines
05-01-2007, 07:58 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

This must be Jerry.
Tried again 4-30-07 after putting neddles back at factory setting at 1 1/2 turns out.
It got a little better.
Not running backwards after Sunday's run.
Waiting on new...
Forum: Gas Engines
05-01-2007, 07:22 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

Still using 91 octane at 25:1 with Lawn Boy less than a gallon thru it so far.
Spark gap in manual says .028 should it be lower as recommened by Don's Hobby?
Forum: Gas Engines
05-01-2007, 07:18 PM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

What gap are you using on your plug? Manual says .028.
I was recommened by Don's Hobby in Salina Ks. that it should be lower.
Forum: Gas Engines
05-01-2007, 12:02 AM
Replies: 389
Views: 73,581
Posted By hics3968

RE: THOR 45 CDI at Hobby People Comments

I'm buliding same GP PW and with Thor 45. Had it running ok while in Salina Ks. never flew because of bad weather.
As i'm back in Arizona cannot get the 7000 rpm I had there with 20-8 apc prop....
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Manage Preferences - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.