RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Vettster
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Forum: Composites Fabrication And Repair
04-27-2019, 12:40 PM
Replies: 30
Views: 13,814
Posted By Vettster

No problem at all.. I appreciate the break from...

No problem at all.. I appreciate the break from my current project. its actually the same project but I did away with the stabs you see in this thread and went with a full flying tail. Getting my...
Forum: Composites Fabrication And Repair
04-27-2019, 12:19 PM
Replies: 30
Views: 13,814
Posted By Vettster

I have switched to Airex too.. so there you go! :)

I have switched to Airex too.. so there you go! :)
Forum: Composites Fabrication And Repair
04-27-2019, 08:55 AM
Replies: 30
Views: 13,814
Posted By Vettster

Sorry its been awhile. Trying my best to remeber...

Sorry its been awhile. Trying my best to remeber the order. your photo helps. Here's the order I used.

1
2
4
5
3
6

1, is a full sheet and bridges the hinge line. There is no separation
Forum: Composites Fabrication And Repair
04-26-2019, 05:18 PM
Replies: 30
Views: 13,814
Posted By Vettster

Hi Reuben... I lay up the peel ply in a sandwich....

Hi Reuben... I lay up the peel ply in a sandwich. First my 4 oz outer skin
then a strip of 4 oz about 4" wide
then the Lancor soric(honeycomb looking stuff) cut to come up to the hinge line on both...
Forum: Composites Fabrication And Repair
03-19-2018, 04:09 PM
Replies: 30
Views: 13,814
Posted By Vettster

Hinge turned out great. I used the peel...

Hinge turned out great. I used the peel ply.https://cimg5.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1500x2000/img_20180319_191239897_712c2574e79cdd67c2e388a4159e3acd95a24a19.jpg...
Forum: Composites Fabrication And Repair
02-17-2018, 03:41 PM
Replies: 30
Views: 13,814
Posted By Vettster

Thanks Greg..but I've found it very easy to cut...

Thanks Greg..but I've found it very easy to cut with the right scissors. You need sarrated scissors.
cheers
Forum: Composites Fabrication And Repair
02-17-2018, 02:05 PM
Replies: 30
Views: 13,814
Posted By Vettster

Charles.. sorry for the late reply.. working long...

Charles.. sorry for the late reply.. working long hours. Thanks very much for taking the time to post what is very interesting info. I think I will be going with kevlar. Water will most likely not...
Forum: Composites Fabrication And Repair
01-26-2018, 05:37 PM
Replies: 30
Views: 13,814
Posted By Vettster

But even though its coated.. you need to pull...

But even though its coated.. you need to pull very hard to get it off.. and dont forget its on top when peeled off. Now if it were sandwiched between two layers of glass? well I think it would be...
Forum: Composites Fabrication And Repair
01-26-2018, 05:34 PM
Replies: 30
Views: 13,814
Posted By Vettster

That's even more interesting because the Red...

That's even more interesting because the Red stripe is used to let you know that the PP is coated. But then again.. it just might be a companies thing.
The coated stuff I use has the Red stripes on...
Forum: Composites Fabrication And Repair
01-26-2018, 04:26 PM
Replies: 30
Views: 13,814
Posted By Vettster

Yup...I got plenty of both. The better would be...

Yup...I got plenty of both. The better would be the dress stuff since the peel ply has a coating to make it easier to remove(not stick aswell) ;)
Forum: Composites Fabrication And Repair
01-26-2018, 03:51 PM
Replies: 30
Views: 13,814
Posted By Vettster

Peel ply!..very good to know.. thanks for the...

Peel ply!..very good to know.. thanks for the tips.
Forum: Composites Fabrication And Repair
01-24-2018, 01:03 PM
Replies: 30
Views: 13,814
Posted By Vettster

Thanks for the info and link Red. ;)

Thanks for the info and link Red. ;)
Forum: Composites Fabrication And Repair
01-15-2018, 10:35 AM
Replies: 30
Views: 13,814
Posted By Vettster

Kevlar Live Hinges?

Hi Guys! Need a grey area cleared up for me. Ive searched many of the other threads but can't seem to find the info I need. Im building a 7 foot long jet and I am going to be using live hinges. ...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.