RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: chadr
Showing results 1 to 9 of 9
Search took 0.08 seconds.
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
10-18-2008, 11:07 AM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

What motor heat sink is going to fit with minimal or no cutting on the rustler? My mamba 4600 is running up to 200 degrees with 16/90 gearing. Castle doesn't have any ideas on why its running so...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
09-10-2008, 10:59 PM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

I use 100% punch control only because it seems to be plenty quick and responsive for me. Is there really much to be gained by reducing it to 30% or so? The track where i drive it is dry clay,...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
09-10-2008, 01:26 AM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

no wheelies for me, i did indeed mean 100% punch control (as in the most gentle to the drivetrain) and my timing is the lowest possible setting. esc temp is barely warm after hours at the track so...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
09-09-2008, 09:16 AM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

I've had the timing all the way down and punch control set to 100% since installing the mm 4600. I just installed a 13t pinion this weekend to run with the 3s a123 pack so I'll see what temps I get...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
09-08-2008, 09:38 PM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

Is there a way to cool down motor temps on a Rustler? I was running 16/87 with a mamba max 4600 motor and temps reached 180 at some times when running 3s a123 without even pushing it at the local...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
08-31-2008, 06:08 PM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

Gotta say the ca tire glue works very well to hold the suspension screws in place. I drove my car almost 4 hours at the track and nothing came loose. I didn't have to stop except when a screw for...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
08-30-2008, 08:31 AM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

Plastic threads - No. 425

yup, the left side rear suspension arm always backs out a little bit. perhaps the engine heat? I am just going to use tire glue for now, can't hurt. If it doesn't...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
08-29-2008, 11:53 PM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

thanks for the feedback fellas.

i have blue threadlock that I've used on my 1/8 buggy on the screws that go into metal. these screws on the rustler that keep coming loose are in plastic. i...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
08-29-2008, 08:20 PM
Replies: 11,114
Views: 756,668
Posted By chadr

RE: Official Rustler Thread

what is the secret to keep the screws holding the front camber links in place. I have an older electric rustler with a plastic one piece non adjustable camber link. Is there a glue that would work...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.