RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: Spychalla Aircraft
Showing results 1 to 9 of 9
Search took 0.02 seconds.
11-01-2019, 02:37 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

To Roger Russell: I have one of these under...

To Roger Russell: I have one of these under construction, but no flight experience with it yet. However, I spoke to two experienced pilots up at Fond Du Lac a year ago about the gear set-up and...
01-08-2019, 03:30 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Rev, I don't know on the need or demand for such...

Rev, I don't know on the need or demand for such wheels, but I do know that to smooth out 3D printed parts there is a modeler named Damon (DAG) who sells engines via Atwood Aviation. He gives his...
07-04-2017, 07:08 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Loco3D, Regarding the CG with the FG-84 Triple. ...

Loco3D, Regarding the CG with the FG-84 Triple. I built one with the stock finish as an ARF and I had to mount my RX battery packs just behind the wing. I had taken the firewall plates off. So it...
06-29-2017, 08:32 PM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Check p.173 post #4312. I detail the whole Sierra...

Check p.173 post #4312. I detail the whole Sierra Gear installation. You have to change your wing dihedral to a scale configuration but it's not that hard. The Sierra Gear are fantastic! The best! Leo
12-22-2016, 11:20 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

OK. Send me a PM with your snail-mail address...

OK. Send me a PM with your snail-mail address and I will send you what you need. I will put together a paper template / plan and some instructions over this Christmas Holiday weekend 12/25/16 and...
12-22-2016, 04:51 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Chris, I have made a mounting design and have...

Chris, I have made a mounting design and have all the details, but it is based on increasing the dihederal of the wing to a scale configuration. I can send out a print-out of the templates in order...
12-21-2016, 04:32 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

No cutting of the firewall. You do need to cut...

No cutting of the firewall. You do need to cut hole in it to accept the carb. The thing to recognize is that this is a 4-Stroke engine and that they don't have the spit-back out of the carb like a...
12-17-2016, 06:07 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Now for something trick on the Saito FG84. A way...

Now for something trick on the Saito FG84. A way to choke that beast without pulling on the barrel of the carb. I built a servo hinged flapper with foam on it that closes when the ignition is...
12-17-2016, 06:00 AM
Replies: 4,698
Views: 833,048
Posted By Spychalla Aircraft

Chris, Here are the close-up pictures you are...

Chris, Here are the close-up pictures you are looking for. Build a stack of plywood to mount it on. Cut the hole for the carb and all. A little dremel work on the corners of the square TF box...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.