RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: EDFCrazy
Showing results 1 to 9 of 9
Search took 0.02 seconds.
Forum: RC Jets
05-26-2016, 03:15 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Just one standard washer like 1mm thick. i didn't...

Just one standard washer like 1mm thick. i didn't think one washer would make such a difference.
Forum: RC Jets
05-25-2016, 01:13 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Add one washer under the front of the engine...

Add one washer under the front of the engine mount on each side, to make the engine's nozzle point a little down. this is all mine needed to not climb at full throttle. VT 80 in mine.
...
Forum: RC Jets
12-25-2015, 07:44 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Vettser, that isnt enough angle. i had about 85...

Vettser, that isnt enough angle. i had about 85 deg in the end, i started with about what you have now, and the difference between that and the 85 deg i have now was enormous. what you have now is...
Forum: RC Jets
01-20-2015, 01:34 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Here is some flight footage of mine with the VT...

Here is some flight footage of mine with the VT 80.

https://www.youtube.com/watch?feature=youtu.be&v=y_wodYawE7E&app=desktop
Forum: RC Jets
01-19-2015, 03:31 PM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Hi, thanks for the compliment. I used savox 1256...

Hi, thanks for the compliment. I used savox 1256 on elevator, sc0252 on ailerons, and sc0251 on flap and hitec 5245 mini on rudders. I used the std ripmax air gear set. I put the airtanks below the...
Forum: RC Jets
01-18-2015, 06:44 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Hi, my xcalibur and VT 80 combo is awesome, loads...

Hi, my xcalibur and VT 80 combo is awesome, loads of power for the verticals. I dont have any problems using my DX9 with the digital trims either. I have a video of mine flying that i still need to...
Forum: RC Jets
09-07-2014, 08:52 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

i Checked every screw on mine and all of them...

i Checked every screw on mine and all of them were lose. i also found one screw that was longer than the rest. And because of this it started to cut into the brake pad. Make sure you check yours.....
Forum: RC Jets
02-17-2014, 04:21 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Sorry, when i saw then red i thought it was a new...

Sorry, when i saw then red i thought it was a new colour scheme. Is there perhaps a new colour scheme in the pipeline?
Forum: RC Jets
02-17-2014, 03:03 AM
Replies: 2,625
Views: 732,218
Posted By EDFCrazy

Is that a new colour scheme?

Is that a new colour scheme?
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.