RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: DaleD
Showing results 1 to 13 of 13
Search took 0.05 seconds.
Forum: Gas Engines
11-05-2013, 12:53 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

From my experience 1/4 turn clockwise = more...

From my experience 1/4 turn clockwise = more closed = more lean. Maybe you have a different carb than the one supplied with my DLE30.

DaleD
Forum: Gas Engines
10-24-2013, 12:34 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

Sounds like you have a fuel mixture issue. Check...

Sounds like you have a fuel mixture issue. Check for air leaks and if you dont find any give your carb a thorough clean.

DaleD
Forum: Gas Engines
10-23-2013, 11:58 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

You will receive different recommendations based...

You will receive different recommendations based on indevidual experiences. I flew a DLE30 for 2 years on the original carb and then changed to a WT793A because it developed an idle issue. I would...
Forum: Gas Engines
08-02-2013, 02:55 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

i've used both 3/32" and 1/8" with success.

daleD
<br type="_moz" />
Forum: Gas Engines
11-14-2012, 08:03 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

I would suggest you look at a 16" prop for three blade. Check out the 16.5x10x3 from Bollyhttp://www.bolly.com.au/models/glassthree.html

DaleD
Forum: Gas Engines
04-17-2012, 03:27 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

<span>A couple posts back in this thread</span>, maybe more than just a couple,<span> the WT-813 was recommended as a suitable replacement for the DLE 30 carb.  Would the WT-805 supplied with the MLD...
Forum: Gas Engines
02-03-2012, 01:07 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

I think the burble is an indication of a slightly right low end. Some modellers will tune their engines this way to facilitate easier starting.

</p>
Forum: Gas Engines
08-28-2011, 04:02 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

This maybe a statement of the obvious but it appears you rotated your carb. My DLE30 was installed straight out the box and the throttle and choke linkages were on the right hand side when facing the...
Forum: Gas Engines
05-26-2011, 05:58 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

Would appreciate suggestions on suitable servos for DLE30 throttle

Thanks
Forum: Gas Engines
05-24-2011, 02:52 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

I have had to replace a Hitec 485 on the weekend. Wondering if this is a good match for the DLE30 on the throttle. I too have heard that standard metal gear servos at best for the throttle, would...
Forum: Gas Engines
11-21-2010, 05:11 PM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

I don't have experience with the CMP Extra 300 but I do have the CMP Yak 54 140. I'm running an MLD28 which is heavier than the DLE 30 and I needed a bit of weight to get her balanced. The DLE30 will...
Forum: Gas Engines
11-19-2010, 11:37 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

</p><div style="margin: 0in 0in 0pt"><span style="font-size: 9pt">Jody,

Maidenmy 73"MX2 with the DLE 30 last weekend and boy, did it handle theMX2 like a rag doll. Totally pleased with this little...
Forum: Gas Engines
11-02-2010, 11:36 AM
Replies: 5,283
Views: 760,408
Posted By DaleD

RE: NEW DLE30!

<p style="MARGIN: 0in 0in 0pt" class="MsoNormal"><span style="FONT-SIZE: 9pt; FONT-FAMILY: "Arial","sans-serif"">I recently bought a DLE30 and its completed installation in the intended home.  I...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.