RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: RepEvox
Showing results 1 to 12 of 12
Search took 0.04 seconds.
08-28-2010, 10:21 AM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

I had a Integy CVD axle pop out. The oring around the hub part of the cvd was pushed to the side and the pin spinned loose.  After I turned the axle just popped out...

Fortunately I just found it...
08-23-2010, 09:50 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Yeah my ball cups are getting sloppy...was thinking about getting aluminum ones or something. I don't think you need the entire hub

joecool, I emailed you back about the screws. I took my bumpers...
08-17-2010, 12:31 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

I guess that's where my inexperience comes in. Thanks man

Kinda unfortunate that I have to keep break the plastic ones. Also, whoever has changed the screws on the TBR bumpers, would it be...
08-16-2010, 08:11 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

I broke a 82MG and now a 85MG. Pretty much my fault for landing on a front tire from about 6 feet in the air...

My bellcrank barely turns under a lot of stress. I have 3 springs so I cut one down...
08-12-2010, 09:21 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

I bought a HR racing bellcrank and I have no problems with it. It was like $18 which is kind of a hassle, but I broke my spare 2 plastic ones.
08-08-2010, 10:48 AM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Stock servo is pretty bad. I suggest getting something stronger. I have a Hitec 85MG coming in and I think that's one of the best one's that fit in the mini revo.
08-07-2010, 11:05 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Alright I'll see what I have. I'm sure CVDs will make it smoother because my plastic shafts are pretty beat up. Also for the screws; I went to Osh and it looked like #3 screws would fit, but then...
08-07-2010, 06:18 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Ah, good idea. Just out of curiosity, do you guys grease the teeth between the diffs and pinions? My car is not rolling smoothly ATM. I just cleaned the whole car as it is used.
08-06-2010, 11:13 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Yeah I'm loving the TBR bumpers on my MERV. I hate the tiny alan screws though. I will definitely strip one of the heads in the future.

Planning to get CVDs throughout, center diff, and new...
07-04-2010, 12:56 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Yeah I understand. I've been reading up on a lot of reviews and overviews to see what's weak or flawed about the merv...not too much people can criticize! I plan to upgrade it as time passes; this...
07-04-2010, 10:14 AM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

Yeah, I was basing some of the upgrades off of this video from Squirrelod

http://www.youtube.com/watch?v=nE6Jc5gbKo4
07-02-2010, 12:57 PM
Replies: 4,457
Views: 685,407
Posted By RepEvox

RE: OFFICIAL MINI E-REVO THREAD!!!

This is why I'm getting one

http://www.youtube.com/watch?v=ZB4ZBtbKAZg&feature=related

...bad song but the footage is pretty sickening
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.