RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Steve
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: 3D Electric Flying!
05-07-2018, 04:34 PM
Replies: 10
Views: 4,527
Posted By Steve

Got my KMX finished up. I used the provided...

Got my KMX finished up. I used the provided method for installing the motor and cowl. Fitted the spinner and prop, and got the first flight jitters out of the way! With the heavier servos in the...
Forum: 3D Electric Flying!
04-26-2018, 04:39 PM
Replies: 10
Views: 4,527
Posted By Steve

https://cimg1.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg1.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1120x747/smd_8551_5adf01cab29048a77c853b02e9fccf94273a3546.jpg...
Forum: 3D Electric Flying!
04-23-2018, 09:05 PM
Replies: 10
Views: 4,527
Posted By Steve

It was a 3 step process to get the carbon side...

It was a 3 step process to get the carbon side plates and glass cloth in place. I trimmed all the excess off, once dried, and put a little epoxy on all the joints as...
Forum: 3D Electric Flying!
04-23-2018, 09:00 PM
Replies: 10
Views: 4,527
Posted By Steve

The next step was to prep the motor box. To glue...

The next step was to prep the motor box. To glue the carbon side stiffeners on, I used 30 minute epoxy. I also cut some plastic strips to rest on top of the carbon plates, then put a piece of foam,...
Forum: 3D Electric Flying!
04-23-2018, 07:33 AM
Replies: 10
Views: 4,527
Posted By Steve

I also got the stab, elevator installed....

I also got the stab, elevator installed. Assembled the rudder and installed it. Sealed the rudder and built the elevator and rudder push...
Forum: 3D Electric Flying!
04-23-2018, 07:05 AM
Replies: 10
Views: 4,527
Posted By Steve

Had some time to get a little more done on my...

Had some time to get a little more done on my KMX. Got all the holes opened up, and installed the rudder and elevator servos....
Forum: 3D Electric Flying!
04-09-2018, 06:40 PM
Replies: 10
Views: 4,527
Posted By Steve

Got some more work done. I glued the elevator...

Got some more work done. I glued the elevator hinges in place. I also like to seal my hinge gaps from the bottom and I happen to have some transparent yellow covering. It worked great to seal the...
Forum: 3D Electric Flying!
04-06-2018, 01:44 PM
Replies: 10
Views: 4,527
Posted By Steve

Got the wings finished up! I had to use the round...

Got the wings finished up! I had to use the round servo horns supplied with the servos, as they matched up best with the holes in the carbon ones. I also sanded the round horns to I didn't get any...
Forum: 3D Electric Flying!
04-05-2018, 04:10 PM
Replies: 10
Views: 4,527
Posted By Steve

I also had a nice surprise in the box, as PA...

I also had a nice surprise in the box, as PA upgraded my servos to the Hitec 5245's instead of the smaller Hitec's that were out of stock. I used my trim iron to seal up the covering around the servo...
Forum: 3D Electric Flying!
04-05-2018, 03:45 PM
Replies: 10
Views: 4,527
Posted By Steve

Ok, Got some work done on the wings! The first...

Ok,
Got some work done on the wings! The first step in the build is to install the aileron horns. I used a small needle file to open up the hole in the horn for the clevis screw. Then I sanded the...
Forum: 3D Electric Flying!
04-05-2018, 11:21 AM
Replies: 10
Views: 4,527
Posted By Steve

Precision Aerobatics Katana MX Build

Got some time to get started on my Katana assembly. My wife bought me the Pro version that comes with the power package and servos. I also picked up a Futaba 7 ch. receiver and some Dubro servo...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.