RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: TPerk
Showing results 1 to 25 of 35
Search took 0.02 seconds.
Forum: Gas Engines
01-06-2014, 10:43 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I was not aware that Hobby King was carrying...

I was not aware that Hobby King was carrying parks for the MGH 38 cc four stroke engine, am I wrong
Forum: Gas Engines
12-31-2013, 12:50 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

Parts up date. I contacted NGH about the loos...

Parts up date. I contacted NGH about the loos rocker arm I have on my engine, it has a lot of side to side movement. NGH emailed me back and said they are going to ship me a new rocker arm to AMR at...
Forum: Gas Engines
12-30-2013, 05:06 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Nice Video Tyor. Thanks for sharing it with us....

Nice Video Tyor. Thanks for sharing it with us. Here is NGH web site where you can contact them, should you need to. http://www.nghengine.com/
Forum: Gas Engines
12-29-2013, 07:43 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Ok I will. AMR had told me that they could get...

Ok I will. AMR had told me that they could get parts, maybe they where not being truthful with me. I am trying to get them to order a new rocker arm, if they do not, I will let you know. I have a...
Forum: Gas Engines
12-29-2013, 06:32 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I have a up date on my engine. After more break...

I have a up date on my engine. After more break in time it is now idling at 1800 RPMs with a19*8 falcon wood prop and RPMs in flight is 7200. I am liking this engine more and more. I am going to go...
Forum: Gas Engines
12-23-2013, 08:14 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi Here is my email [email protected] The...

Hi Here is my email [email protected] The NGH 38cc is heavier engine then the DLE I have 11.1 volt 2200 battery close to the back of the yank and a 11.4 2200 battery 6" behind the CG see...
Forum: Gas Engines
12-22-2013, 03:06 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi Alfiev I don't know about shipping to New...

Hi Alfiev I don't know about shipping to New Zealand. The guy name Dany seem to be most helpful, I hope they can help you with the shipping.
Forum: Gas Engines
12-22-2013, 09:36 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I know that a 1/4 gal is not much, when I have...

I know that a 1/4 gal is not much, when I have used up the gas and oil mix that I am using for break in gas and oil mix I will use a 40:1 mix and I am using Ams synthetic 2 stroke oil. I have been...
Forum: Gas Engines
12-22-2013, 05:18 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Thanks. I have been turning it in a little bit at...

Thanks. I have been turning it in a little bit at a time and I am at the point where, if I turn it in any more the engine will not run at all. I am still running the break in gas and oil. I have...
Forum: Gas Engines
12-22-2013, 04:41 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi I order my NGH 38cc 4 stroke from AMR they had...

Hi I order my NGH 38cc 4 stroke from AMR they had it in stock and have free shipping. here is the site...
Forum: Gas Engines
12-19-2013, 12:57 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

As far as I know it does not really matter witch...

As far as I know it does not really matter witch line you put where. As far as using a muffler, you don't really need one, the engine is not very noisy, at least not as I am concerned. I think it...
Forum: Gas Engines
12-16-2013, 06:50 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Once again, Thanks

Once again, Thanks
Forum: Gas Engines
12-16-2013, 03:58 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi SJN, I had sent a copy of the video I had...

Hi SJN, I had sent a copy of the video I had posted on here to Mr. Tan from NGH and he thinks I should be using a 19*8 or a 20*8 prop for better idle. The engine that you said where getting 1800 rpms...
Forum: Gas Engines
12-15-2013, 10:11 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I run the engine some more and adjusted the...

I run the engine some more and adjusted the timing, it did seem to idle a bit better. I adjusted the carb some and got it to idle at 2500 if I tried to get it lower say about 2000, it will not stay...
Forum: Gas Engines
12-15-2013, 07:48 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I will do that, I hope to run the engine some...

I will do that, I hope to run the engine some more this afternoon and I will get back to you.
Forum: Gas Engines
12-15-2013, 07:18 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I will give it a try and see what happens, I need...

I will give it a try and see what happens, I need to adjust the carb some more any way, How did moving the timing sensor do with the engines idle, Did it help a lot or just a little bit? Thanks...
Forum: Gas Engines
12-15-2013, 06:55 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi Tyor, I am going to try and run the engine...

Hi Tyor, I am going to try and run the engine some more to day, I will run it and check the rpms then move the sensor closer to the magnet and run it again and check the rpms and see what it looks...
Forum: Gas Engines
12-15-2013, 06:00 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

I am sending you a couple of pic of my NGH 38 cc...

I am sending you a couple of pic of my NGH 38 cc engine set to TDC, the pick up magnet at TDC seems so far away from the pickup sensor Does this look right, From what you can see in these pix, do you...
Forum: Gas Engines
12-14-2013, 03:35 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

Wow the plane looks great I am sure you will a...

Wow the plane looks great I am sure you will a lot of fun with it.
Forum: Gas Engines
12-14-2013, 03:33 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

I will let you know as soon as I can run the...

I will let you know as soon as I can run the engine again and play with the timing, it may be a week or so. I used a 18*8 prop and may try a APC thin blade prop 18*8 or a 18*10. I think the prop I...
Forum: Gas Engines
12-14-2013, 03:03 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

Thank you so much for the info. I thought that...

Thank you so much for the info. I thought that the engine was not running well because it is not really broken in yet, I will look in to setting the timing. So far I really like this engine, sounds...
Forum: Gas Engines
12-14-2013, 02:04 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

I did check the valves and had to set one of...

I did check the valves and had to set one of them. There are gaskets between the carb and manifold. I did not check the timing, I am not sure just how to check the timing, I do know where to adjust...
Forum: Gas Engines
12-14-2013, 01:46 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

Hi guys, I was able to get a flight in today on...

Hi guys, I was able to get a flight in today on my 30cc Pitts with a NGH 38cc four stroke engine today. Engine run good at high RPM idle was a bit high the bets I could not get it to idle down, it...
Forum: Gas Engines
12-06-2013, 03:48 AM
Replies: 1,678
Views: 456,406
Posted By TPerk

Thanks again, I started up mine yesterday, I had...

Thanks again, I started up mine yesterday, I had to adjust the carb a pretty good bit. I guess it needed more adjustments then normal, the gas tank is about 40mm higher then the carb, I hope that the...
Forum: Gas Engines
12-03-2013, 03:02 PM
Replies: 1,678
Views: 456,406
Posted By TPerk

I for got to ask what you guys are setting the...

I for got to ask what you guys are setting the plug gap at, The manual sucks
Showing results 1 to 25 of 35
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.