RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: nine o nine
Showing results 1 to 25 of 98
Search took 0.08 seconds.
Forum: RC Warbirds and Warplanes
11-24-2014, 02:30 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

1 1/8 idle needle and 1 1/4 high speed openings...

1 1/8 idle needle and 1 1/4 high speed openings is a good place to start.
Forum: RC Warbirds and Warplanes
10-21-2014, 11:19 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Hi Jaketab, The gas tubing I found was perhaps...

Hi Jaketab, The gas tubing I found was perhaps for a stove installation. The ID was just the right size for a push fit. A hose clamp won't work unless you slit it where the clamp needs to be. I...
Forum: RC Warbirds and Warplanes
10-20-2014, 02:06 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I use the corrugated stainless tubing made for...

I use the corrugated stainless tubing made for natural gas hookups. Bends are possible with the stuff. Looks cool too! Mitch
Forum: RC Warbirds and Warplanes
10-09-2014, 03:47 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I fully agree about reducing the intake area and...

I fully agree about reducing the intake area and enlarging the exit for better cooling....1 to 3 at least. Not only that but directing the airflow around the cylinder fins rather than AT them if...
Forum: RC Warbirds and Warplanes
07-27-2014, 09:37 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I've used my supplied socket for the 5 or 6 years...

I've used my supplied socket for the 5 or 6 years I've owned a Moki. If it's possible you might try drilling new cross holes a bit lower than what you have. I've also found that using stout rod...
Forum: RC Warbirds and Warplanes
07-12-2014, 10:37 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I haven't myself but I heard one a few years ago...

I haven't myself but I heard one a few years ago I think it was at Rhinebeck. it didn't have the nice throaty sound that the collector gives and it wasn't loud. I love the cadence of a...
Forum: RC Warbirds and Warplanes
06-30-2014, 03:17 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Hi Whit, Get the correct sized "real" socket on a...

Hi Whit, Get the correct sized "real" socket on a 3/8" drive ratchet handle and give it a short rap with a light hammer. If that doesn't loosen the grip on the plugs.......maybe hire someone who's...
Forum: RC Warbirds and Warplanes
06-23-2014, 09:05 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Glad you had good results with the regulator. ...

Glad you had good results with the regulator. Mitch
Forum: RC Warbirds and Warplanes
06-11-2014, 04:03 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

32x18 is perfect for the 250 with static RPM in...

32x18 is perfect for the 250 with static RPM in the 4200 to 4600.range. Mitch
Forum: RC Warbirds and Warplanes
06-09-2014, 02:53 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

+1 Mitch

+1 Mitch
Forum: RC Warbirds and Warplanes
06-08-2014, 12:22 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Could be a shut down in the module because of too...

Could be a shut down in the module because of too much voltage...that's what you're thinking and it's possible. Interesting to hear your results. Mitch
Forum: RC Warbirds and Warplanes
06-08-2014, 11:03 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

The old modules can use nicad,nimh, Life,...

The old modules can use nicad,nimh, Life, LiPoly....as long as the voltage can be regulated to about 4.8 to 5.8 volts. I use a 2300mah Life to my fuel pump at 6.3V and split through a regulator to...
Forum: RC Warbirds and Warplanes
06-08-2014, 09:08 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I'm told by users that the new ignition doesn't...

I'm told by users that the new ignition doesn't add any performance but it allows the use of unregulated LIFE and Lipo voltages. I also expect that the new one has much better reliability. MItch
Forum: RC Warbirds and Warplanes
06-01-2014, 04:43 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I doubt that the coils got damaged but I guess...

I doubt that the coils got damaged but I guess it's possible. Do a continuity check on each wire in the cable.. If the grey plastic outer got a hole melted in it it's possible that the wire...
Forum: RC Warbirds and Warplanes
05-08-2014, 12:35 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I agree that a single 2500 mh A123 will easily...

I agree that a single 2500 mh A123 will easily power the pump and ignition. My plane averages a 250mh draw with a ten minute flight. It would be a good idea as suggested to measure the draw on your...
Forum: RC Warbirds and Warplanes
04-18-2014, 03:25 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Hi Mike, The 43--4400RPM is perfect with that...

Hi Mike, The 43--4400RPM is perfect with that prop. It'll unload more in the air and everything will improve with more runtime including the black gunk. That's normal as all parts are seating in. ...
Forum: RC Warbirds and Warplanes
04-07-2014, 12:29 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Hi gentlemen, I could be wrong but the new...

Hi gentlemen, I could be wrong but the new ignition works on the 215/250 400 too but these still use the internal spark coils and not the the electronic spark box with new leads. Can anyone confirm...
Forum: RC Warbirds and Warplanes
03-24-2014, 01:17 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

The 180 sounds terrific....only...

The 180 sounds terrific....only question....you're not going to have the ailerons and elevators with that much throw I hope. I guess that sounded like my wife saying "you're not wearing THAT tonite...
Forum: RC Warbirds and Warplanes
01-20-2014, 04:49 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

Since the engine started and ran ok on the ground...

Since the engine started and ran ok on the ground after an inflight failure with the tank about 1/2 full I'd suspect the fuel tank supply line. It may have either stiffend over time and is staying...
Forum: RC Warbirds and Warplanes
01-02-2014, 11:40 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

From my 4 stroke motorcycle racing...

From my 4 stroke motorcycle racing days...smoothing the radii in the intake and exhaust manifolds and heads makes for a smoother mixture flow but may or may not change performance. What will help...
Forum: RC Warbirds and Warplanes
12-19-2013, 04:41 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

The solid light means power is on and the blink...

The solid light means power is on and the blink occurs when spark is made. Mitch
Forum: RC Warbirds and Warplanes
12-13-2013, 02:24 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

We're talking only about the liquid Seafoam fuel...

We're talking only about the liquid Seafoam fuel additive right? What about the Seafoam brand penetrating oil and lube in the spray can for hitting the valve stems and rockers a good idea too or will...
Forum: RC Warbirds and Warplanes
12-13-2013, 12:17 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

I'd like to learn more I about Seafoam products...

I'd like to learn more I about Seafoam products I and their use for the Mokis. Any users with advice?
Forum: RC Warbirds and Warplanes
06-11-2013, 07:00 PM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

RE: MOKI RADIAL Care and Maintenence

I use a single oil inlet at the top of the exhaust ring. The amount of smoke produced is extrodinary since there's of heat generated inside the pipe., Mitch
Forum: RC Warbirds and Warplanes
01-13-2013, 05:06 AM
Replies: 5,152
Views: 1,361,585
Posted By nine o nine

RE: MOKI RADIAL Care and Maintenence

It's most likely only economically usable for parts. If the accesories are in good shape...ignition module, electric pump if installed I'd make an offer. Mitch
Showing results 1 to 25 of 98
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.