RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: skunkwurk
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Forum: RC Jets
08-22-2021, 04:24 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

I have not been on rcu all season, looking...

I have not been on rcu all season, looking forward to following this project again.
Forum: RC Jets
01-15-2021, 04:05 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

nice!

nice!
Forum: RC Jets
10-11-2020, 03:44 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

What paint scheme?

What paint scheme?
Forum: RC Jets
10-06-2020, 05:57 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Gary - Nice to see the wax lacing. We use it...

Gary - Nice to see the wax lacing. We use it quite a bit in the Data Center. I use it on my jets as well - looks great!
Forum: RC Jets
10-01-2020, 05:47 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

Gary, are you planning on painting the interior...

Gary, are you planning on painting the interior of the fuse?
Forum: RC Jets
09-21-2020, 05:08 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Or a clump of hysol.

Or a clump of hysol.
Forum: RC Jets
09-20-2020, 05:19 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

These look great and like the idea of using 4mm -...

These look great and like the idea of using 4mm - I’m going to test them on my next build. I am planning a 1/7th scale F15.

Thank you for sharing!
Forum: RC Jets
09-19-2020, 06:41 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

I'm sorry if you have already mentioned this...

I'm sorry if you have already mentioned this earlier in the thread, but can you share who the manufacturer is for the non-jet-tronics valves? The two with the orange base.
Forum: RC Jets
09-18-2020, 03:01 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

You’re welcome.

You’re welcome.
Forum: RC Jets
09-18-2020, 02:49 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

I would have to pull my radio out and look...

I would have to pull my radio out and look through the screens to remember exactly how I did it, but it was a mix to provide a percentage of left or right travel when the gear switch was in a up...
Forum: RC Jets
09-18-2020, 02:36 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Sounds like she is putting up a fight. Im sure...

Sounds like she is putting up a fight. Im sure you’ll get her! A friend of mine has a large Mig-29 that puts up a pretty tough fight every time we work on her. On the Mig I had to program a nose...
Forum: RC Jets
09-16-2020, 05:00 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

I would also test with the production flight...

I would also test with the production flight hardware (valves & tanks). I see you adjusted pressure down, that is a good test. But the volume of air you’re able to push from the air compressor is...
Forum: RC Jets
09-16-2020, 03:53 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Looks great!

Looks great!
Forum: RC Jets
09-15-2020, 06:29 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

Perhaps take a progressive approach? Cut the slot...

Perhaps take a progressive approach? Cut the slot and close the doors to see how it looks. Maybe even paint the hinge to match the white of the intake. If it bothers you after you get a good look at...
Forum: RC Jets
08-28-2020, 04:24 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

I'm pretty sure he's already considered that...

I'm pretty sure he's already considered that idea. I bet he is trying to keep both sides symmetrical and with equal geometry. Symmetry is one of my (OCD) obsessions.
Forum: RC Jets
08-19-2020, 05:39 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

wow. What a nice job, incredible. Well done, sir!

wow. What a nice job, incredible. Well done, sir!
Forum: RC Jets
12-04-2019, 07:29 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Hi Gary, Any work coming on this bird? ...

Hi Gary,

Any work coming on this bird? Looking forward to seeing how it comes together.
Forum: RC Jets
09-03-2019, 04:32 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

I'm ordering some icing too. BTW - hands...

I'm ordering some icing too.

BTW - hands down the best build thread currently ongoing. Honestly - love that it is one of B1 Bob's kits too, even though she needs a little tlc to get her done.
Forum: RC Jets
09-12-2018, 06:07 AM
Replies: 978
Views: 199,949
Posted By skunkwurk

I lost about a month - I have seen practically...

I lost about a month - I have seen practically all of them, it is a lot of content. Pretty amusing too.
Forum: RC Jets
09-11-2018, 03:42 PM
Replies: 978
Views: 199,949
Posted By skunkwurk

Great build. looking forward to following it. I...

Great build. looking forward to following it. I miss good ole B1-Bob's videos...
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.