RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: F3A Nordic
Showing results 1 to 16 of 16
Search took 0.02 seconds.
Forum: Gas Engines
04-27-2019, 09:34 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Jeff I have same problem . Found carb set at an...

Jeff
I have same problem . Found carb set at an angle, was lucky that i have not finnished throttle
linkage installation and did minor modification of pushrod.
First was it impossible to install...
Forum: Gas Engines
04-04-2019, 12:34 PM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Jeff Yes i did manufacture a new timing ring...

Jeff
Yes i did manufacture a new timing ring december 2018 after i had checked timing on this engine on each cylinder.
Did no engine run with saito timing ring due to this timing issue.
Have now...
Forum: Gas Engines
04-04-2019, 09:28 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

I bought My engine 2018 and sending picture i...

I bought My engine 2018 and sending picture i think it is new design cylinder on this engine.
Have now installad Morris intake kit .
Forum: Gas Engines
02-23-2019, 12:28 PM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Check post # 1849 and you have photo of new...

Check post # 1849 and you have photo of new design piston.
Remove ignition plug and you can check piston.
Forum: Gas Engines
01-19-2019, 02:27 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Cathurga Sorry for your engine break down. ...

Cathurga
Sorry for your engine break down.
Yes that's a lot of carbon in combustion chamber.
Is it same on all cylinder, i can understand if don't want to remove all cylinder to check but i think...
Forum: Gas Engines
01-15-2019, 12:54 PM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

757 Jonp I think it is clear that this engine...

757 Jonp
I think it is clear that this engine TDC Spacing is not 0, 120, 240.
Several people have checked ther engine's and have same result.
This is my First radial engine and i am also surprised...
Forum: Gas Engines
01-12-2019, 04:53 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Hello again Cartuga Spacing #1 to #2 magnet...

Hello again
Cartuga
Spacing #1 to #2 magnet 126 degree. Spacing #2 to #3 magnet 108 degree. Spacing #3 to #1 magnet 126 degree.
I think this is correct Spacing but due to my cheap tool during...
Forum: Gas Engines
01-11-2019, 09:43 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Hello I have made a new prop hub based on my...

Hello
I have made a new prop hub based on my check of timing on My new engine.
Have used Proxxon dividing attachment 24264 to drill Hole for each magnet.
My goal was to have timing each cylinder...
Forum: Gas Engines
11-21-2018, 01:42 PM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Slither TDC cylinder 2 126 degree, cylinder 3...

Slither
TDC cylinder 2 126 degree, cylinder 3 234 degree.
You can check with 360 degree wheel and piston stop.
Forum: Gas Engines
11-21-2018, 08:17 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Slither This engine is not symetrical 3...

Slither
This engine is not symetrical 3 cylinder radial.
If everthing would be perfect it would be 120 degree 120 degree 120 degree but due to connecting Rod design it is not symetrical. Have...
Forum: Gas Engines
11-12-2018, 08:19 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Thanks for your video Adrian and for Quick and...

Thanks for your video Adrian and for Quick and easy solution to change timing to 30 degree.
Now i understand how the ignition box is designed to work on this engine.
I have your timing kit with...
Forum: Gas Engines
11-09-2018, 07:00 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

I would be nice if some people from saito factory...

I would be nice if some people from saito factory team could give some help to sort out issue regarding
timing. But if you connect ignition box and igniter plugs and have spark close to 28 before...
Forum: Gas Engines
11-08-2018, 11:55 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Have now checked timing on my new engine. First...

Have now checked timing on my new engine.
First i used the instructions from ch ignitions to check radial engine ( when green light come on)
Timing cyl 1 45,5. Cyl 2. 51. Cyl 3. 39,5.
...
Forum: Gas Engines
11-03-2018, 05:26 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

Morris mini motor have made a video with some...

Morris mini motor have made a video with some information regarding timing on this engine.https://youtu.be/Nh2ZKOnx904.
conlusion stock engine timing not perfect.
Forum: Gas Engines
10-29-2018, 12:51 PM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

I have also checked this web page ch ignitions...

I have also checked this web page ch ignitions and have one timing check kit on order.
Expecting timing to be 28-30 on my new Saito fg60r3 engine on each cylinder.
I am also confused on how to...
Forum: Gas Engines
10-21-2018, 11:51 AM
Replies: 2,806
Views: 703,499
Posted By F3A Nordic

I have checked ch ignitions.com web page and have...

I have checked ch ignitions.com web page and have reading in download page how to use timing tool for muti cylinder engine timing. Timing is when green led on.
Single cylinder timing is when green...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.