RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Jack Diaz
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Forum: RC Jets
11-20-2018, 05:43 AM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Gary, my mistake !! Wherever I wrote "SE", I...

Gary, my mistake !! Wherever I wrote "SE", I meant "SB".
In Function Assigment, you assign L1 for the gear.
MX is a telemetry control.

Jack
Forum: RC Jets
06-30-2018, 05:57 AM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

One more thing: It is VERY important to...

One more thing:

It is VERY important to remember to set the gear switch in the Down position if the failsafe is triggered.
The reason is that you may not have steering, since in some...
Forum: RC Jets
06-29-2018, 07:58 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Hi Goose, a telemetry dropout will not drop the...

Hi Goose, a telemetry dropout will not drop the gear if you program as my Method 2 above. That's the whole purpose of that logic.
I have used MBar as failsafe in most of my planes for years without...
Forum: RC Jets
06-29-2018, 06:13 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Hi Wayne, As far as I know, there is no way to...

Hi Wayne,
As far as I know, there is no way to avoid the "clear" command from momentaneously interrupting all telemetry input. Nonetheless there are a couple of ways to avoid that issue affecting...
Forum: RC Jets
06-05-2018, 01:58 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

I agree !!!!! Making 99% of their users...

I agree !!!!! Making 99% of their users scared with the "Q" value !!!! :) :) :)

Jack
Forum: RC Jets
06-04-2018, 03:06 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Gabriel, The receivers send information to the...

Gabriel,
The receivers send information to the transmitter everytime they receive an information package. In other words, there is an acknowledgment of package received.
The transmitter counts the...
Forum: RC Jets
06-04-2018, 11:09 AM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Gabriel, a Q = 0 doesn't mean you had no signal. ...

Gabriel, a Q = 0 doesn't mean you had no signal.
The transmitter wasn't listening to the receiver, but the receiver was receiving OK, except for an instant at 403.


Jack
Forum: RC Jets
05-31-2018, 04:41 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Dave, both receivers are receiving and sending 24...

Dave, both receivers are receiving and sending 24 channels to the CB via EXBus.
On Device Explorer you define which of the 24 channels correspond to each servo output of the CB.
Also, on Device...
Forum: RC Jets
05-31-2018, 04:32 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Wayne: did you read my post # 886 ??? Here...

Wayne: did you read my post # 886 ???

Here is a copy paste :)

Dave, in Device Explorer, assign channels 16 and 17 to outputs ports 1 and 2 of your RX3. Power patch port 3 of RX3 (a Y from one...
Forum: RC Jets
05-31-2018, 04:16 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

No Dave .... "you use both receivers" !! Only...

No Dave .... "you use both receivers" !! Only that channels 16 and 17 are connected to one of them ... it really doesn't matter to which one.
Forum: RC Jets
05-31-2018, 02:23 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

Dave, in Device Explorer, assign channels 16 and...

Dave, in Device Explorer, assign channels 16 and 17 to outputs ports 1 and 2 of your RX3. Power patch port 3 of RX3 (a Y from one of the CB200 servo outputs). Output 4 of RX3 goes to CB200 as...
Forum: RC Jets
09-29-2017, 05:41 AM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

I heard that your post bumped you to the bottom...

I heard that your post bumped you to the bottom of the list :) :) :)
Forum: RC Jets
09-16-2017, 01:35 PM
Replies: 2,111
Views: 496,034
Posted By Jack Diaz

https://www.youtube.com/watch?v=Fmf7AbRzEgU&list=P...

https://www.youtube.com/watch?v=Fmf7AbRzEgU&list=PLvyEb4dPIJVetgP-GI6Wry8lmP-krwIES&index=10&t=6s
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.