RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Ultracon46
Showing results 1 to 19 of 19
Search took 0.02 seconds.
Forum: Marketplace
07-19-2019, 10:24 AM
Replies: 0
Views: 105
Posted By Ultracon46

Merco .35 muffler?

Looking for a Merco muffler for a Merco .29/.35.
01-06-2018, 07:14 PM
Replies: 32
Views: 12,301
Posted By Ultracon46

Dan, I am trying to refurbish my old K&B 23 and...

Dan, I am trying to refurbish my old K&B 23 and would like to change out the head bolts from phillips to hex cap bolts. Is there any info, anywhere in this world that gives me greenhead part numbers...
Forum: Glow Engines
01-04-2018, 07:13 PM
Replies: 16
Views: 2,421
Posted By Ultracon46

True. I just like dunking the thing in a pot of...

True. I just like dunking the thing in a pot of clean water.
Forum: Glow Engines
12-24-2017, 09:58 AM
Replies: 2
Views: 794
Posted By Ultracon46

Will do... BTW it's an Arden .09. Found that on...

Will do... BTW it's an Arden .09. Found that on the backplatee after cleaning.
Forum: Glow Engines
12-20-2017, 07:51 PM
Replies: 2
Views: 794
Posted By Ultracon46

Arden .19 glow plug engine!

I just got a couple of ugly looking old engines on Ebay. Turns out with a cleaning, they are pretty nice. One is an Arden .19. Still turns smoothly with that huge plug on top. Is this engine of any...
12-16-2017, 11:26 PM
Replies: 14
Views: 1,222
Posted By Ultracon46

I have JB Weld as a staple in my tools. Are you...

I have JB Weld as a staple in my tools. Are you saying I should JB Weld the carb to the fitting over the hole the same size as the id on the shank of the carb? I was thinking about a tube that will...
12-16-2017, 06:26 PM
Replies: 14
Views: 1,222
Posted By Ultracon46

The intake on the Sabre is about 7.5 mm o.d. If...

The intake on the Sabre is about 7.5 mm o.d. If I can fit a brass tube or aluminum tube over that, then I can use an Enya .09 carb. But how to do that is the question. Probably too much heat for...
12-11-2017, 09:02 AM
Replies: 14
Views: 1,222
Posted By Ultracon46

Small engine carb?

Do they make carbs that fit small (1.5cc) diesels? I would love to put a throttle on my old DC Sabre.....
12-10-2017, 06:27 PM
Replies: 3
Views: 587
Posted By Ultracon46

GOT THAT SPINNER OFF! Used the old seize up cure...

GOT THAT SPINNER OFF! Used the old seize up cure of a pot of boiling water. Stuck the engine in the pot with just the spinner immersed, jammed up the rear of the crank shaft, used a padded vise...
Replies: 20
Views: 6,868
Posted By Ultracon46

Thanks! That is what I needed to know. ...

Thanks! That is what I needed to know. Appreciate the help!
Replies: 20
Views: 6,868
Posted By Ultracon46

Can you still fly FM frequencies?

I have an old Hitec Prism 7 that I would like to use. I have been out of the hobby for many years. Can I still fly with an FM 72 mhz frequency radio?
Forum: Control Lines
12-08-2017, 06:13 PM
Replies: 229
Views: 69,771
Posted By Ultracon46

A Wenmac plastic Corsair. On a cold day on the...

A Wenmac plastic Corsair. On a cold day on the golf course my Dad suffered and finally started the Cox .049. One huge loop into the ground and it was done... So much for my incredible Christmas...
12-08-2017, 09:42 AM
Replies: 14
Views: 3,751
Posted By Ultracon46

I know this is an old thread, but I just boil a...

I know this is an old thread, but I just boil a pot of water, take it off the stove and dunk the engine, carb, whatever in the hot, HOT water. You engine will free up in less than a minute!
Forum: Glow Engines
12-07-2017, 07:43 PM
Replies: 16
Views: 2,421
Posted By Ultracon46

I know this is an old thread, but dunking it in a...

I know this is an old thread, but dunking it in a pot of water just after the water boils. Boil the water, then take it off the stove and dunk the engine for a few minutes. It will cure all oil...
Forum: Glow Engines
12-07-2017, 07:39 PM
Replies: 35
Views: 13,488
Posted By Ultracon46

I know this is an old thread but what I do is...

I know this is an old thread but what I do is boil a pot of water, take if off the stove and then dunk the engine or the carb, whatever you want to free up, and in seconds, the old oil is melted and...
12-07-2017, 01:13 PM
Replies: 3
Views: 844
Posted By Ultracon46

Great idea! Thanks!

Great idea! Thanks!
12-07-2017, 01:11 PM
Replies: 3
Views: 587
Posted By Ultracon46

Many thanks Aussie! I am a former Kiwi. I have...

Many thanks Aussie! I am a former Kiwi. I have had the engine totally apart, and cleaned, except of course the crankshaft. I try your idea with a piece of wood today!
12-06-2017, 07:43 PM
Replies: 3
Views: 587
Posted By Ultracon46

Angry Help! D-C Sabre with a seized prop spinner nut

I have an old D-C Sabre 1.5 cc diesel I am trying to resurrect. Worst problem I have is the seized prop spinner nut. The engine comes with a red metal spinner which is the prop nut. It has a hole...
12-06-2017, 07:38 PM
Replies: 3
Views: 844
Posted By Ultracon46

Angry D-C Sabre, 1.5 cc diesel

I have an old D-C Sabre diesel I am trying to resurrect. Worst problem I have is the seized prop spinner nut. The engine comes with a red metal spinner which is the prop nut. It has a hole drilled...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.