RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: manleywc
Showing results 1 to 18 of 18
Search took 0.73 seconds.
Forum: Marketplace
10-13-2021, 07:52 PM
Replies: 1
Views: 470
Posted By manleywc

Wanted: 3-Blade Prop for DA-170

I'm looking for a three blade prop for my DA-170. Mejzlik or Falcon, 29x12 or 28.5x12.
I'm also looking for a matching 5" Ultimate Style Tru-Turn spinner.
06-15-2003, 04:20 AM
Replies: 0
Views: 544
Posted By manleywc

Convert ZDZ 160 to 3W 150 Prop Bolt Pattern?

Is there a prop hub available for the ZDZ 160 that will allow me to use my props and spinners that are drilled for a 3W-150?

Thanks,
Cliff
[email protected]
04-06-2003, 12:43 AM
Replies: 3
Views: 821
Posted By manleywc

Very Old AE RC 300 On-road Car?

Thanks for the replies. I will pass on this deal, since the parts seem to be hard to get. I wouldn't buy it just to make a buck on Ebay, but I did pass this information along to the seller.
...
04-04-2003, 03:18 AM
Replies: 3
Views: 821
Posted By manleywc

Very Old AE RC 300 On-road Car?

My neighbor wants to sell me a very old (~1980) Associated RC 300 on-road car. The car is a complete kit, unassembled in the original box. The price is very good, and I already have several 20-size...
Forum: Gas Engines
02-06-2003, 10:27 PM
Replies: 23
Views: 2,305
Posted By manleywc

I fixed It!!!

Hi everyone,

I fixed the engine. It was an air leak at the phenolic block. Sanding did not fix it. I had to buy a new block. The recess where the thick black seal sits can not be sanded flat. ...
Forum: Gas Engines
01-14-2003, 02:32 AM
Replies: 5
Views: 607
Posted By manleywc

3w-140 Problem Update

Where should I buy the replacement carburetor? Is there an upgrade to the current Walbro WGA-7?

Mike,

I may have over tightened the parts, but I also put gasket sealer between all the...
Forum: Gas Engines
01-13-2003, 03:11 AM
Replies: 5
Views: 607
Posted By manleywc

3w-140 Problem Update

This is an update to my problem with my 3W-140 B2F posted a few weeks ago. Thanks to all of those for there help, but I don't think I fixed the problem yet.

Here's the current situation:
At less...
Forum: Gas Engines
01-04-2003, 03:33 PM
Replies: 23
Views: 2,305
Posted By manleywc

3w-140 problem

Thanks for the reply Kris. I did find evidence of a leak at the thick neoprene seal between the valve block and fiberglass insulator. It was wet with gas across the seal in two places. the 4...
01-04-2003, 03:23 PM
Replies: 3
Views: 926
Posted By manleywc

Modern Ski Boat Kit or Plans?

Thanks for the reply Ron.
01-02-2003, 03:12 AM
Replies: 3
Views: 926
Posted By manleywc

Modern Ski Boat Kit or Plans?

Does anyone know of a kit or plans for a modern ski boat, such as a Mastercraft Prostar 190, or similar boat? I have seen one used to tow a water-skiing squirrel. I don't plan to tow any small...
Forum: Gas Engines
01-01-2003, 12:25 AM
Replies: 23
Views: 2,305
Posted By manleywc

3w-140 problem

Answer to Diablo:
I'm using a Stihl filter. It has a cylindrical plastic housing with a fine mesh filter element. It has very low flow resistance, and is still heavy enough to stay at the low...
Forum: Gas Engines
12-31-2002, 02:28 AM
Replies: 23
Views: 2,305
Posted By manleywc

3w-140 problem

Answer to Walt:
Both needles are set rich at about 2 turns out. Original factory settings were 1-1/2 turns.

Answer to Bob:
I get a lot of mixed information on Octane. I have found very little...
Forum: Gas Engines
12-30-2002, 04:37 AM
Replies: 23
Views: 2,305
Posted By manleywc

3w-140 problem

This one is long and complicated, but I'm really stumped here. Any help would be greatly appreciated.

Here's the main problem, my 3w-140 B2F quits while inverted, at low to medium throttle.

It...
Replies: 4
Views: 466
Posted By manleywc

How Do I Tighten-up 5925/5945 Gears?

Thanks for the help. Can a resin/plastic gear set be used in the 59XX servos?
Replies: 4
Views: 466
Posted By manleywc

How Do I Tighten-up 5925/5945 Gears?

Mike,

I have 2 HS-5925's on each wing of my 37% Extra, and 1 HS-5945 on each elevator. I am very satisfied with all aspects of the servos, except for the slop at center. I am concerned about...
Forum: Gas Engines
11-07-2002, 07:35 PM
Replies: 6
Views: 715
Posted By manleywc

Confession Details

I cut off the front two stacks, leaving about 1/2" of pipe protruding from the main can. I then brazed two .030 aluminum disks of into the pipe ends. I attached a picture with the cowl on. I'm...
Forum: Gas Engines
11-07-2002, 01:38 PM
Replies: 6
Views: 715
Posted By manleywc

Thanks and Confession

Thanks for the replies.
I guess I should also tell on myself. I took some bad advice and cut-off, then capped the front stacks on these mufflers. The engine is very quite, but does not seem to...
Forum: Gas Engines
11-06-2002, 03:30 PM
Replies: 6
Views: 715
Posted By manleywc

Cleaning out black sludge buildup in mufflers?

How do I clean out the black sludge building up in my 3W-140 stock can mufflers? I've tried several solvents and oven cleaner. I think the baffle holes are becoming clogged, restricting airflow. ...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.