RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Brendan Lugo
Showing results 1 to 25 of 500
Search took 0.66 seconds.
Replies: 2
Views: 734
Posted By Brendan Lugo

RE: Freedom 9S & ID

It's a remote link button in case your rx instilation does not allow you to get to the one thats on the rx itself.
Replies: 15
Views: 2,876
Posted By Brendan Lugo

RE: JR12X and Spectra 2.4J

The JR module has been available for a couple months already. #29537
Replies: 4
Views: 671
Posted By Brendan Lugo

RE: optic 6 has stoped working

Are you sure the transmitter battery is fully charged? If it's low it would power teh LED but not the LCD. Also if the battery was plugged in backwards then damage has occured and the radio would...
Replies: 2
Views: 1,629
Posted By Brendan Lugo

RE: Disassembling Hitec HS-7955TG, how?

You would have to unsolder the 3 motor tabs from the pc board first.
Replies: 5
Views: 1,186
Posted By Brendan Lugo

RE: Aurora 9 Update issue

If you cant get the radio to come back on by re-updating it then send it in.
Replies: 1
Views: 720
Posted By Brendan Lugo

RE: Telemetry GPS

No it wont cause a problem.
Replies: 1
Views: 586
Posted By Brendan Lugo

RE: power reccomendations for A9 setup

It should be fine with direct battery power. Make sure any extensions you are using are heavy duty with good gold plated connectors.
Replies: 2
Views: 791
Posted By Brendan Lugo

RE: Spectra Mod (pn 28315) w/ Futaba 9C ???

Yes it does wotk in Futaba radios that use the Futaba TP-FM module. This info will not be on the website or in the instructions to protect the feelings of a certain Corporation. ;)
Replies: 11
Views: 1,264
Posted By Brendan Lugo

RE: HS-985MG behavior - Is this Normal or need to be fixed?

Per your same post.
http://www.rcgroups.com/forums/showthread.php?t=1412805
You provided more info here. So you are using a BEC which is now set to 6 volts. What is the amperage of this BEC as it...
Replies: 1
Views: 1,621
Posted By Brendan Lugo

RE: Question about aurora update

They do sort of the same thing other then mixes can overthrow what the EPA % is set to. Travel limit is a hard stopping point so mixes cannot overthrow what you have set in T. Limit and bind up a...
Replies: 7
Views: 4,297
Posted By Brendan Lugo

RE: Hitec HG-5000 gyro drifts

All of our specs show input voltage of 4.5 - 5.5 volts for the gyro. I dont show a 6 volt rating for the gyro and have never heard you can damage it by doing the auto calibration. Where did you hear...
Replies: 17
Views: 1,400
Posted By Brendan Lugo

RE: Servo Programer software link no good?

Check or turn off your AV (anti virus) software. It may be causing the issues you are having as the link is working.
Replies: 6
Views: 3,572
Posted By Brendan Lugo

RE: Hitec HTS-Voice Telemetry Voice Announcing System, anybody have one..??

The voice module won't be available until mid year. The navi we should be receiving any time.
Replies: 4,979
Views: 831,461
Posted By Brendan Lugo

RE: New Hitec Aurora 9-Channel 2.4Ghz Radio System

If upgrading from an old v1.05 or v1.06 version then yes. If updating from v1.07(x) then no. V2.0 on the module is still the latest firmware.
Replies: 7
Views: 1,693
Posted By Brendan Lugo

RE: Hitec 645 MG Servo Failure?

If he had to replace the gears twice in it chances are he had also damaged the top case support for the center gear shaft and that should have also been replaced. What probably happened was he...
Replies: 7
Views: 1,693
Posted By Brendan Lugo

RE: Hitec 645 MG Servo Failure?

The 6XX series has always been a very popular sport level servo. I dont know what your buddy is using them in but if he's going through them like that then he's got something setup incorrectly or...
Replies: 2
Views: 591
Posted By Brendan Lugo

RE: Programming Question 7955

Use them straight out of the box. You only need the programmer if you want to change them from their factory settings or are ganging multiple servos to a single control..
Replies: 7
Views: 4,297
Posted By Brendan Lugo

RE: Hitec HG-5000 gyro drifts

On setting the servo limit you need to hold the rudder stick to the left just to where the tail starts to bind and press the button, then do the same for the right side. In Bobs video I think he took...
Replies: 7
Views: 4,297
Posted By Brendan Lugo

RE: Hitec HG-5000 gyro drifts

Does it not do this in rate mode? If not then I dont think it's defective, but rather not set up properly. Watch "Finless Bobs" setup of that gyro on helifreaks and set it up that way. If it is still...
Replies: 4
Views: 692
Posted By Brendan Lugo

RE: Recommendation for HD servo?

If you are already looking at the 5805MG then your other option would be the 5755MG. Torque and speed is about the same but the 5755MG is slightly smaller (more true of a 1/4 scale size servo) and...
Replies: 4
Views: 692
Posted By Brendan Lugo

RE: Recommendation for HD servo?

Not enough information is given about the aircraft to be able to give any kind of recommendation.
Replies: 6
Views: 851
Posted By Brendan Lugo

RE: HITEC FREE 7 CH. RECEIVER.

As with warranty for product, it's purchased and used in those territories which we cover.
Replies: 1
Views: 565
Posted By Brendan Lugo

RE: PROGRAMING DIGITAL SERVOS

The output gear is connected to the pot shaft so ther eis no adjustment there.
Replies: 6
Views: 851
Posted By Brendan Lugo

RE: HITEC FREE 7 CH. RECEIVER.

Please note that this is a special offer that only HITEC USA is providing for it's customers. The other Hitec distributors could do this in their country if they wanted to. These are the rules for...
Replies: 5
Views: 1,076
Posted By Brendan Lugo

RE: Hitec 5998tg 5997tg

#55310 does not exist. The gear you need (shown in the picture) is the output gear. You will need to contact your Hitec importer/service center to be able to get that gear.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.