RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: gade600sdi
Showing results 1 to 25 of 298
Search took 0.31 seconds.
Forum: Gas Engines
03-14-2013, 09:15 AM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

You are correct, dont ever use paper gaskets on any Rc muffler!! Clean both engine and muffler with alcohol. Spread a very thin amount on both sides of red permatex (high temp silicone from any...
Forum: Gas Engines
03-14-2013, 09:09 AM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

Does this engine have enough power to Hover your 7 pound Katana? Did you weight come out exactly at 7 pounds box stock with this engine on?
03-13-2013, 08:21 AM
Replies: 824
Views: 198,449
Posted By gade600sdi

RE: Hangar 9 30cc P-47 Build Thread

Curt,

Just curious on your thoughts of using auxiliary power instead of powering the retracts through the Rx? Robart says you can do either in the instructions, but I was wondering the...
03-12-2013, 12:32 PM
Replies: 824
Views: 198,449
Posted By gade600sdi

RE: Hangar 9 30cc P-47 Build Thread

Nick, have you flown this model yet. Still waiting for your maiden report. I opened mine up last night and unpacked everything. Its been sitting all winter on the shelf and I need to either get...
Forum: Gas Engines
02-28-2013, 05:38 AM
Replies: 27
Views: 4,140
Posted By gade600sdi

RE: RotoFlow Fuel Tanks

Its a gimmick. Its heavy with all that brass. The seals wont last and when one fails, you will suck air and leak fuel in your plane. Could result in a dead stick. Proven tank is dubro or sullivan...
Forum: ARF or RTF
02-13-2013, 08:58 AM
Replies: 7
Views: 2,791
Posted By gade600sdi

RE: Hangar 9 Funtana 125 Balance point

The pulse 125 floats well. Mine is toward the back of the range they show in the manual, more AFT but still in the manual range. Dont make it nose heavy you dont need it. Also, consider moving...
02-06-2013, 07:33 AM
Replies: 824
Views: 198,449
Posted By gade600sdi

RE: Hangar 9 30cc P-47 Build Thread

Spridal,

Your question above I don't understand how is it holding up with a DLE 55. It should really be turned around, how does it hold up with the Evo 40, which is heavier. The DLE 55 is...
Forum: Gas Engines
02-04-2013, 01:17 PM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

I think you can get that 3 ounces of weight back by carrying 3 ounces less fuel....don't forget about the fuel difference, its not really a weight issue. As a matter of fact, you now have ability to...
Forum: Gas Engines
01-15-2013, 10:44 AM
Replies: 185
Views: 41,292
Posted By gade600sdi

RE: DLE-85 85cc Gas Engine at troybuiltmodels.com

I like the carb they have a long throw arm in the picture, nicer looking throttle hookup, but I don't see an integrated choke lever hole?
Forum: Gas Engines
01-14-2013, 10:04 AM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

Has anyone done any real testing with this engine with some numbers/stats. Like a chart with various prop sizes and rpm's and static thrust measured with a laptop like the magazines do sometimes (RC...
Forum: Gas Engines
01-04-2013, 08:38 AM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

I have been doing some calculation on weight vs. the Evolution 60NX engine.

Evolution 10cc Gas is 23 ounces all in. (book says 22 but I used the guy that weighed it on a scale in this forum)...
Forum: Gas Engines
12-13-2012, 09:50 AM
Replies: 2,224
Views: 399,128
Posted By gade600sdi

RE: New Evolution 10cc gas engine

I expect this to be a top quality engine. I have an Evolution 80GX and an Evolution 26GX gas engines. I also have some other DLE and an OS and a Zenoah. I have to say that the two Evolution...
Forum: ARF or RTF
11-30-2012, 12:30 PM
Replies: 32
Views: 3,437
Posted By gade600sdi

RE: HANGAR 9 PULSE 125 XT

I would not say the Revolver is more aerobatic, they are both basic beginner to intermediate airobatic planes. The Pulse 125 is much larger than the revolver 70. I have one and yes it does float in...
Forum: Gas Engines
11-16-2012, 09:36 AM
Replies: 6,892
Views: 1,073,310
Posted By gade600sdi

RE: NEW DLE 20cc Gasser! (Data & Links 1st Post)

Did you change over now to the DLE55 ignition now without the idle "step"?
Forum: Gas Engines
11-16-2012, 08:42 AM
Replies: 6,892
Views: 1,073,310
Posted By gade600sdi

RE: NEW DLE 20cc Gasser! (Data & Links 1st Post)

I agree fully, the seam means nothing and may not work in all instances. You have to do it the right way with a TDC gauge, dial indicator, and degree wheel. Mine was definately at 38 BTDC and I flew...
Forum: Gas Engines
11-16-2012, 07:51 AM
Replies: 6,892
Views: 1,073,310
Posted By gade600sdi

RE: NEW DLE 20cc Gasser! (Data & Links 1st Post)

w8ye,

No I am not turning the engine over backwards!!! I rotated the crank the way the prop rotates counter clockwise. Dont know how you could have possibly derived that comment from what I...
Forum: Gas Engines
11-16-2012, 06:55 AM
Replies: 6,892
Views: 1,073,310
Posted By gade600sdi

RE: NEW DLE 20cc Gasser! (Data & Links 1st Post)

My DLE 20 has not been running as perfect as I like, so I checked a few things over and one of them was ignition timing. The book says 28-30 degrees BTDC for the Rxcel ignition. So I made up my...
Forum: ARF or RTF
11-14-2012, 07:16 AM
Replies: 2,036
Views: 387,945
Posted By gade600sdi

RE: New Hangar 9 1/4 Scale P 18 Super Cub

Would it be stupid to put smoke on this unit? Would there be room for the tank and the pump?
Forum: 3D Flying!
11-08-2012, 01:12 PM
Replies: 19
Views: 1,922
Posted By gade600sdi

RE: Twist 60 knife edge?

I agree it plain flys like crap in certain aspects. It is a beater plane. Does good at certain things and is good windy day plane that you dont have too much money to loose, but I woulndt waste a...
Forum: Gas Engines
11-02-2012, 08:52 AM
Replies: 6,892
Views: 1,073,310
Posted By gade600sdi

RE: NEW DLE 20cc Gasser! (Data & Links 1st Post)

This is not a DLE 20 problem, but a geometry problem. Use a long arm on your carb and a small one on your servo. Set your travel to 100% on high and low and adjust the angle and the lenght of the...
10-25-2012, 11:32 AM
Replies: 6
Views: 1,028
Posted By gade600sdi

RE: makeing smoke oil

Does super dri smoke oil eat up covering and foam, or is it safe on covering. Maybe it never forms oil on your covering in the first place to eat it up...hence the term super dri?
Forum: ARF or RTF
10-25-2012, 06:04 AM
Replies: 1,604
Views: 265,810
Posted By gade600sdi

RE: Seagull Yak?

Make sure your Yak is reliable engine. This model is fine when under power, when it loses power it becomes a flying brick. 3 of them at our club and all are no longer with us after the first dead...
Forum: ARF or RTF
10-25-2012, 05:52 AM
Replies: 2,036
Views: 387,945
Posted By gade600sdi

RE: New Hangar 9 1/4 Scale P 18 Super Cub

I think based on what was said above, they have it set up for a G26 magneto. G26 EI will be lighter and need lead, but even this is very heavy compared to a DLE30. So I do not agree with above...
10-18-2012, 08:50 AM
Replies: 824
Views: 198,449
Posted By gade600sdi

RE: Hangar 9 30cc P-47 Build Thread

So I saw a couple warnings about using heavy wire and polarity on the retracts from Robart. But, how many guys are using them and there are no issues? I can deal with setup issues and getting the...
Forum: Gas Engines
10-17-2012, 08:40 AM
Replies: 8
Views: 3,101
Posted By gade600sdi

RE: Throttle linkage for Gas engines

I should have said what Pete said BALL LINKS meaning on each end. Just dont use any clevises. I agree with the throttle spring also, I usually try to unhook it and move it to the next hole so the...
Showing results 1 to 25 of 298
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.