Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: mrich_30047
Showing results 1 to 15 of 15
Search took 0.42 seconds.
03-16-2009, 04:54 AM
Replies: 7
Views: 1,262
Posted By mrich_30047

RE: Anyone running Blade 400 with Align 430x motor

Yes I'm running the stock ESC with the 430XL. The stock Eflite motor and the 430XL are close enough that there is no problem. I did have to ream out the motor mount hole slightly to use the Align...
03-14-2009, 06:12 AM
Replies: 7
Views: 1,262
Posted By mrich_30047

RE: Anyone running Blade 400 with Align 430x motor

I'm running the 430XL motor in my blade. i used a 11 tooth pinion. I did this because there is not enought metal in the smaller count pinion due to the larger 3mm shaft. I think that your target of...
11-20-2008, 05:31 AM
Replies: 8
Views: 2,790
Posted By mrich_30047

RE: Blade 400 gyro upgrade

James:

Before you give up on the stock gyro try a new tail servo. I installed a JR 3500 and the 110 gyro holds well. just buy a second boom mount and shorten the pushrod.
09-21-2008, 06:43 AM
Replies: 5
Views: 886
Posted By mrich_30047

RE: Blade 400 blade tracking

Did you replace the Dampners? These can affect the tracking as you add pitch.
09-07-2008, 06:43 AM
Replies: 20
Views: 1,725
Posted By mrich_30047

RE: let's see those B400 pics.

Here's mine with a new canopy from Helidirect. The canopy is fiberglass and the same size as the stock canopy.
Forum: T-Rex heli
06-14-2008, 05:01 AM
Replies: 16
Views: 4,116
Posted By mrich_30047

RE: Punching full throttle from hover and tail kicks out.

It sounds like your throttle curve is too low.
Are you in Idle up when you punch the throttle and the tail kicks out?
06-05-2008, 05:44 AM
Replies: 362
Views: 90,416
Posted By mrich_30047

RE: Blade 400 - Tips, tricks, and mods

Wolfpackin:

Here's the link where I posted the repair.
http://bladecprepair.com/smf/index.php?topic=2346.0

I didn't have a failure, but was trying to track down gyro problems.
I noticed...
06-04-2008, 05:38 AM
Replies: 362
Views: 90,416
Posted By mrich_30047

RE: Blade 400 - Tips, tricks, and mods

I just replaced the bearings in my motor.
he factory bearings looked like they had no grease/oil in them.
I got my Blade 400 in late December 2007.
The bearings are 3x7x3, I found that the...
05-28-2008, 04:50 AM
Replies: 10
Views: 1,026
Posted By mrich_30047

RE: Auto rotation help please

Here's a link for Helifreak and Bob "Finless". He shows how to do Autorotations in the Sim.
9/2007 - Autos in real life with "STICK CAM" showing the sticks
First up is how to learn to do Auto...
Forum: T-Rex heli
05-27-2008, 04:50 AM
Replies: 11
Views: 2,715
Posted By mrich_30047

RE: TRex 450 SE V2 tail drive belt

If you are going to order a new belt, you might consider this one. Better than the stock Align.

http://www.ronlund.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=heli&Product_Code=MAVHT1003
02-28-2008, 06:46 AM
Replies: 17
Views: 7,923
Posted By mrich_30047

RE: Blade 400 Main Rotor Blades

You can use the wood blades for a long time. Even the woodies will cause a bent feathering shaft in a tip over. I'm presently using the Align 325mm Pro woodies. They are a bit lighter and track well....
02-22-2008, 06:31 AM
Replies: 3
Views: 747
Posted By mrich_30047

RE: Need Help B400

Check the tail rotor shaft, I bet it's bent. Had a similar vibration on my Blade 400 and tracked it down to a bent shaft.
02-18-2008, 04:28 PM
Replies: 3
Views: 524
Posted By mrich_30047

RE: Best parts source - B400

My local "Hobby Town" has most all of the parts for the Bale 400. Anything that Horizon shows as backordered is still upavailble.
02-16-2008, 12:44 PM
Replies: 9
Views: 925
Posted By mrich_30047

RE: B400, very touchy

First i would set the stick tension, the radio book tells how to do that. It might be that you need more tension on the sticks. Next try adding EXPO, this will reduce the input around the Zero stick...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.