RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: athos341
Showing results 1 to 25 of 35
Search took 0.72 seconds.
04-18-2008, 10:40 AM
Replies: 0
Views: 326
Posted By athos341

carb setings on a Pico 60

Does anyone know the carb settings on a Pico 60? It is a dual needle valve with a spray bar that covers the needles and I can not remove the carb to see where the needles are. So I am hoping someone...
Forum: Gas Engines
12-01-2006, 10:33 PM
Replies: 41
Views: 3,022
Posted By athos341

RE: Range Check Problem

Check your spark plug and make sure you do not have a carbon ball on the bottom. Make sure that your spark plug wire is not loose were it goes into the coil. Try changing your ignition/kill switch....
Forum: Gas Engines
11-25-2006, 07:20 PM
Replies: 10
Views: 733
Posted By athos341

Smoke oil

What makes the best smoke? Have a zdz 160cc with TME smart smoke pump.
Forum: Gas Engines
10-28-2006, 11:50 AM
Replies: 1
Views: 935
Posted By athos341

RE: Help on starting a Quadra 42 gas engine.

First loosen your mag. Then take a dollar bill and fold it long ways once and then again. Then place it between the mag and the flywheel. tighten the mag. You should have to turn the engine over to...
Forum: Gas Engines
10-28-2006, 08:16 AM
Replies: 1
Views: 662
Posted By athos341

ZDZ 160 Carb????

What carb is on the older 160. I just got one from someone with a Walbro wb27. It runs off of crank pressure tap from a hose to the top of the crank instead thwe one through the phenolic block. In...
08-18-2006, 09:27 PM
Replies: 1
Views: 558
Posted By athos341

Looking for an article from Joe nall

I flew a Balsa Usa Ercoupe at night at the nall and was told there was an article done it. Has anyone seen this article and could you point me in the right direction. Thank you George Welcome
Forum: IMAC
08-09-2006, 09:56 AM
Replies: 26
Views: 2,183
Posted By athos341

RE: Thumbs or fingers?

I have been flying for 30 yrs now and fly everything from trainer to Jets, Cubs to 3d and fly all the same way. Fingers and thumbs. I have found I get a much better feel and fly with almost no expo...
Forum: Gas Engines
02-12-2006, 08:08 AM
Replies: 9
Views: 1,305
Posted By athos341

RE: twin cylinder problem

I have 4 of them with no changes from stock and no problems? What oil and mix are you running? What break-in prop? what temp is she running at in the air? Is your cowl baffled?
Forum: Gas Engines
02-12-2006, 07:47 AM
Replies: 15
Views: 3,158
Posted By athos341

RE: Zenoh G-62 Ignition system?

if you're putting it in a warbird leave her stock. If your using her for any other application get her conveted to ignition. use Ralph
Forum: Gas Engines
02-12-2006, 07:32 AM
Replies: 3
Views: 379
Posted By athos341

temp parameters for a Brison 106cc

Anyone know the running temp for the 106cc Brison. On the ground I'm at about 200 but have not gotten her back into the air yet. So she may be a little cooler. Cowl is baffled.
Forum: Gas Engines
02-04-2006, 06:13 PM
Replies: 8
Views: 1,951
Posted By athos341

RE: prop position on hand start for zenoah (g26)

All my gas engines I mount the prop the same. I turn the engine over to compression, then mount the prop at 2 o'clock. This way as I flip my hand comes off the prop at 11 and not towards the ground...
02-04-2006, 06:02 PM
Replies: 37
Views: 3,144
Posted By athos341

RE: BAFFLES ???

I baffle all four sides of all my cowls so that the airflow from the openings in front of my cylinders has no choice but to go over the cylinders. I get them as close as possible. My DA100 in normal...
02-04-2006, 02:34 PM
Replies: 1
Views: 285
Posted By athos341

Valve settings for a Magnum 90 4cycle

Does anyone know the valve the valve settings for a Magnum 90 4cycle? Thank you
01-30-2006, 12:39 PM
Replies: 1
Views: 504
Posted By athos341

paint to match Towerkote red

Anyone know the match? The closest I have come in a spray can is Chevy Block Orange, It's very close but not quite right. Please help. Thank you
Forum: Gas Engines
01-22-2006, 11:44 AM
Replies: 15
Views: 723
Posted By athos341

RE: What size prop is best for the Brison 106cc

With the Brison 106cc, Hitec 645mg per surface 2 6v 2100mah and covered in Towerkote I am at 24.75lbs. She is a little heavy. I bought her used and on the first flight The engine came off the...
Forum: Gas Engines
01-21-2006, 07:09 PM
Replies: 15
Views: 723
Posted By athos341

RE: What size prop is best for the Brison 106cc

I will switch them next weekend and let you know. My Da 100 was broke in on a mez 27x10 and now the prop tips are sonic so I had to go to the 28x10. When I'm done switching props I will let you know....
Forum: Gas Engines
01-21-2006, 08:56 AM
Replies: 15
Views: 723
Posted By athos341

RE: What size prop is best for the Brison 106cc

High 7's low 8's depending on the Humidity here in Florida. The prop noise is unbelievable.
Forum: Gas Engines
01-20-2006, 10:38 PM
Replies: 15
Views: 723
Posted By athos341

What size prop is best for the Brison 106cc

I have a Brison 106cc that I have been flying on a menz 26x10 wood but this seems small. Both in regards to rpm and my da 100 throws a 28x10. If I talk to Brison they say a 26x10. Has anyone tried...
01-11-2006, 08:19 AM
Replies: 78
Views: 7,075
Posted By athos341

RE: Starting big Gassers when alone....

All these safety devices are excellent but if you accidently get hit by the prop, you fall, anything at all, 911 will not be showing up on a hunch. IF A TREE FALLS IN THE WOODS AND NO ONE IS AROUND,...
01-11-2006, 06:25 AM
Replies: 78
Views: 7,075
Posted By athos341

RE: Starting big Gassers when alone....

Quite simply you should as a rule never fly alone. You never know what could happen and if by yourself there will be no one to help you if there is an emergency. Now with that being said in 29 years...
01-11-2006, 06:24 AM
Replies: 78
Views: 7,075
Posted By athos341

RE: Starting big Gassers when alone....

Quite simply you should as a rule never fly alone. You never know what could happen and if by yourself there will be no one to help you if there is an emergency. Now with that being said in 29 years...
01-10-2006, 11:21 PM
Replies: 3
Views: 644
Posted By athos341

Nav lights for a Cub????

Where does the landing light go on a cub?
01-10-2006, 07:29 PM
Replies: 32
Views: 4,596
Posted By athos341

RE: 1/4 scale Cub builders

For those looking for gasser's, I have mounted a Kalt 25 w/ electronic ignition in mine and it fits beautifully with only a hole to prime and a slot in the bottom for the spark plug wire. I have a...
Replies: 20
Views: 2,782
Posted By athos341

RE: Are Futaba and Hitec dual conversion rx crystals interchangeable?

yes you can, So long as the hitec receiver is set up for futaba then you can use a futabe crystal or a hitec crstal made for Futaba. There are no differences other then the system they are designed...
06-26-2005, 12:13 PM
Replies: 4,231
Views: 543,116
Posted By athos341

RE: Hostetler 33% Decathlon

There isn't flaps on the decathelon. Not really needed because of wing area on take off and fuse drag on landing. Short field take-offs and slip landings.
Showing results 1 to 25 of 35
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.