RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: w8ye
Showing results 1 to 25 of 500
Search took 0.85 seconds.
Forum: Gas Engines
05-27-2019, 05:18 PM
Replies: 13
Views: 1,966
Posted By w8ye

Appears to have been run hot?

Appears to have been run hot?
Forum: Gas Engines
04-07-2019, 04:00 AM
Replies: 6
Views: 539
Posted By w8ye

keep using the 20:1 or you will loose the...

keep using the 20:1 or you will loose the connecting rod
Forum: Gas Engines
04-04-2019, 12:19 PM
Replies: 5
Views: 372
Posted By w8ye

Use a Barrel nut type mounting setup whereby the...

Use a Barrel nut type mounting setup whereby the nut has a sleeve that extends through the prop washer
Forum: Gas Engines
03-01-2019, 07:16 PM
Replies: 7
Views: 380
Posted By w8ye

Fuel tank position would only have CG and total...

Fuel tank position would only have CG and total weight considerations as fuel draw or siphoning are not part of the picture because of the pump and regulator of the carburetor.
Forum: Sport Flying
01-03-2019, 04:57 PM
Replies: 133
Views: 37,718
Posted By w8ye

+1

+1
Forum: Gas Engines
12-31-2018, 11:39 PM
Replies: 4
Views: 223
Posted By w8ye

Yes

Yes
Forum: Gas Engines
10-29-2018, 02:12 AM
Replies: 16
Views: 505
Posted By w8ye

+1

+1
Forum: Gas Engines
10-29-2018, 02:11 AM
Replies: 3
Views: 287
Posted By w8ye

You can just use a RCEXL ignition.

You can just use a RCEXL ignition.
Forum: Gas Engines
06-11-2018, 09:38 PM
Replies: 6
Views: 527
Posted By w8ye

Take the fuel out of the tank is all I do

Take the fuel out of the tank is all I do
Forum: Glow Engines
05-18-2018, 08:58 PM
Replies: 12
Views: 539
Posted By w8ye

Strong akaline cleaners are responsible for the...

Strong akaline cleaners are responsible for the discolored castings.

For cleaning an engine without the ugly oxidation, use Prestone automotive antifreeze heated but not boiling. Keep engine...
Forum: Gas Engines
04-24-2018, 03:24 PM
Replies: 9
Views: 624
Posted By w8ye

There's two sides to your carburetor, the pump...

There's two sides to your carburetor, the pump side which includes a diaphragm and two check valves. Then there is the regulator side that includes a diaphragm that operates a needle and its seat...
Forum: Gas Engines
04-23-2018, 10:11 AM
Replies: 9
Views: 624
Posted By w8ye

The needle is not fully seating in ZDR regulator...

The needle is not fully seating in ZDR regulator side of the carburetor.
Forum: Gas Engines
03-29-2018, 08:44 PM
Replies: 9
Views: 1,325
Posted By w8ye

+1

+1
Forum: Gas Engines
03-29-2018, 12:06 PM
Replies: 9
Views: 1,325
Posted By w8ye

ahicks, Very good explanation. Had one of these...

ahicks, Very good explanation. Had one of these myself back then.
Forum: Gas Engines
03-11-2018, 01:53 PM
Replies: 6
Views: 579
Posted By w8ye

The planetary output is the 1st thing to go. But...

The planetary output is the 1st thing to go. But they work well until then.
Forum: Gas Engines
12-27-2017, 10:40 AM
Replies: 13
Views: 537
Posted By w8ye

People put 15cc four strokes in them

People put 15cc four strokes in them
Forum: Gas Engines
12-23-2017, 06:32 PM
Replies: 1
Views: 417
Posted By w8ye

Frank V. Ponteri of Maryville, TN and the AMA ...

Frank V. Ponteri of Maryville, TN and the AMA Passed away on Aprill 8, 2013
Forum: Gas Engines
12-15-2017, 03:23 PM
Replies: 3
Views: 978
Posted By w8ye

Regulator diaphragm in the carb may have gone...

Regulator diaphragm in the carb may have gone stiff?
Forum: Gas Engines
12-01-2017, 10:47 AM
Replies: 4
Views: 642
Posted By w8ye

.5mm or .020" but many people run them at...

.5mm or .020" but many people run them at .025"
Forum: Gas Engines
11-27-2017, 07:44 AM
Replies: 4
Views: 458
Posted By w8ye

Get a new fuel inlet and install it in the direct...

Get a new fuel inlet and install it in the direct you want.

Pull the old one out and push the new one in.

You can not turn them as they will break or collapse.

They are available from hobby...
Forum: Gas Engines
11-20-2017, 03:21 PM
Replies: 4
Views: 362
Posted By w8ye

The engine is a NGH 38 2245835

The engine is a NGH 38

2245835
Forum: Gas Engines
11-19-2017, 10:22 AM
Replies: 4
Views: 362
Posted By w8ye

Typically when a model four stroke drops a valve,...

Typically when a model four stroke drops a valve, It also bends all the mechanism. In the long run, it requires a new head assembly.
Forum: Gas Engines
11-12-2017, 11:10 AM
Replies: 10
Views: 534
Posted By w8ye

The mag has to be far enough from the flywheel so...

The mag has to be far enough from the flywheel so it doesn't hit.
Forum: Gas Engines
11-10-2017, 10:00 PM
Replies: 71
Views: 6,988
Posted By w8ye

Send the degree wheel to Tower for checking the...

Send the degree wheel to Tower for checking the timing by turning the engine backwards and claiming its 42 degrees and putting it in all their DLE manuals
Forum: Gas Engines
11-08-2017, 05:54 AM
Replies: 4
Views: 560
Posted By w8ye

It doesen't help vibration at all

It doesen't help vibration at all
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.