RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: ciressarg
Showing results 1 to 12 of 12
Search took 0.09 seconds.
02-27-2008, 01:55 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Ken,
What header are you going with? Mine is also a bit "peaky". Have you tried loading the engine a bit more with a 27x10? That is my plan, but I still have more breaking in to do.

Eric
02-07-2008, 04:03 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Well I snuck out to the field and got in one flight before my cell phone rang. My DA 85 ran very good the entire flight. I kept it up pretty high, I'm still a little shell shocked from the two dead...
02-06-2008, 02:50 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

I have DXF files for the outside and inside shapes. You are welcome to them. don't be surprised if a shop wants $150.00+ per piece for a short run. There is probably at least $20.00 in aluminum...
02-02-2008, 05:30 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Well I managed two brief flights today, both ended in a dead stick after about two minutes. The airplane came down safely. I tracked the problem to a regulator switch wired incorrectly delivering 7.5...
02-01-2008, 03:34 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Here is my throttle servo mount, sorry about the picture quality. I was having problems getting enough light for a good picture.
It's basically just a box made out of 1/8" ply with the bottom of...
01-31-2008, 04:06 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

It turns out it's a 2-56 just a bit sloppy. I was using a metric screw by mistake it threaded in perfectly, but wouldn't go through the ball. I brought my camera to work today, but I forgot my USB....
01-30-2008, 01:43 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

I did my pre balance last night. I was very pleased to have the batteries under the wing tube. I thought for sure I would need them in the nose. They must be coming out a little nose heavy with the...
01-24-2008, 01:05 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Ken,
Am I supposed to use the long all thread Rod for the rudder horns or the short one. I'm guessing the long. Also what's the final verdict on cuting a hole in the fire wall?

Eric
01-23-2008, 01:14 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Not much about 3/8" I think. I know that some of the other kit manufacturers are recomending cutting out the fire wall for the 85. There is quite a few engine mount sugestions for the 85 on FG. I...
01-17-2008, 02:57 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

Made a little progress last night, here are some pics as promised. I didn't have to modify the tunel because I shortened the header. You could leave it the full 12" and cut a hole at the back of the...
01-16-2008, 01:53 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

I got the 85 and can put in mine last night. I had to cut away the intire air scoop that was molded in the cowl. I'm using a rear dump KS so I opened up the bottom of the fuse at the back of the...
01-11-2008, 07:08 PM
Replies: 285
Views: 35,172
Posted By ciressarg

RE: PAU 36% Edge 540 Assembly

I got mine today. It arrived unharmed. Very well packed and well made, I wish I had orded my other stuff sooner. I guess I can put stickers on it, control horns and ELE servo's. The rest will be here...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.